Onkyo TX-NR809 Connecting the Antennas, Connecting the Power Cord, North American

Page 21

Connecting the Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

North American and	European, Australian and
Taiwan models	Asian models

			Insert the plug fully
Push.	Insert wire.	Release.	into the jack.

Insert the plug fully into the jack.

Assembling the AM loop antenna	Caution

• Be careful not to injure yourself

when using thumbtacks.

Thumbtacks, etc.

AM loop antenna (supplied)	Indoor FM antenna (supplied)

Note

•Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible reception.

•Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

Tip

•If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

•If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna.

Connecting the Power Cord

1 Connect the supplied power cord to the AV receiver’s AC INLET.

To AC wall outlet

2 Plug the power cord into an AC wall outlet.

Note

•Before connecting the power cord, connect all of your speakers and AV components.

•Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.

•Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV receiver and should not be used with any other equipment.

•Never disconnect the power cord from the AV receiver while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the AV receiver.

En

21

Image 21

Contents TX-NR809 10 cm 4 at the rear. The rear edge of the shelf or Local regulations when disposing of batteriesBoard above the apparatus shall be set 10 cm Away from the rear panel or wall, creating a flue-likePrecautions Installing the batteries Supplied AccessoriesAiming the remote controller TransmissionContents Services available may vary depending on the region FeaturesAmplifier ProcessingTHX Select2 Plus Front Panel Front & Rear PanelsNorth American and Taiwan models European, Australian and Asian modelsDisplay Front L/R, CENTER, Surr L/R, SB/FH/FW Subwoofer Rear PanelZone 2 and Zone 3 PRE/LINE OUT jacks Front L/R, CENTER, Surr L/RControlling the AV Receiver Remote ControllerDimmer button Display button Muting button Controlling the tunerConnecting Your Speakers Connecting the AV ReceiverConnecting the Speaker Cables Screw-type speaker terminalsSpeaker Connection Precautions Speaker ConfigurationAttaching the Speaker Cable Labels Number SpeakersUsing a Powered Subwoofer Using Dipole SpeakersBi-amping the Front Speakers TipConnecting a Power Amplifier About AV Connections Connecting AV componentsAV Cables and Jacks Hdmi cableAudio Return Channel ARC function Connecting Components with HdmiJack Components Assignable Audio Return Channel is set to AutoEFG Connecting Your ComponentsJack/Port Components Assignable How to record a video sourceConnecting a Recording Component Connecting Onkyo uComponentsSystem On/Auto Power On Remote ControlConnecting the Power Cord Connecting the AntennasPlug the power cord into an AC wall outlet North AmericanTurning On/Off the AV Receiver AV receiver enters standby modeTurning On Turning OffControlling Contents of USB or Network Devices Selecting the Language for the Onscreen Setup MenusPlayback Playing the Connected ComponentUnderstanding Icons on the Display Playing an iPod/iPhone via USBEnter Listening to Internet Radio Playing a USB DeviceListening to Other Internet Radio Registering My Favorites*1Top menu of Internet Radio Windows Media Player 12 Setup Windows Media Player 11 SetupPlaying Music Files on a Server Remote PlaybackUsing the Tuner Using Remote PlaybackTuning into Radio Stations Listening to AM/FM RadioPresetting AM/FM Stations Using RDS excluding North American and Taiwan modelsMode Displaying Radio Text RT Finding Stations by Type PTYListening to Traffic News TP Using the Automatic Speaker Setup Using Basic FunctionsMeasurement procedure First measurement position` Cancel When you’ve finished making the settings, pressUse q/wto select a target, and use e/rto change the setting Press Enter Disconnect the speaker setup microphoneChanging the Speaker Setup Manually Error MessagesSelecting Listening Modes Using the Listening ModesAbout Listening Modes Following audio formats are supported by the listening modeExplanatory Notes Input SourceListening Modes Onkyo-Original DSP Listening ModesDSD*6 DTSTHX Audyssey DSX *8Listening Mode Description Input Speaker Source Layout Using the Home Menu Using the Sleep TimerSetting the Display Brightness Displaying Source Information Using the Whole House ModeChanging the Input Display VCR/DVRSelecting Speaker Layout Using HeadphonesMuting the AV Receiver Press Receiver followed by SP Layout repeatedly to selectRecording Using Easy MacrosOn-screen Setup Menus Advanced SetupCommon Procedures in Setup Menu Explanatory NotesMonitor Out Input/Output AssignComponent Video Input Hdmi InputBD/DVD, VCR/DVR, CBL/SAT, GAME, PC TV/CD, PHONO, Port BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX TV/CD, PHONO, PortSpeaker Settings Speaker SetupDigital Audio Input Analog Audio InputFront Subwoofer PhaseCenter*1, Surround*1, Surround Back*2*3*4 Front Wide*1*2*4, Front High*1*2*4Speaker Distance Wireless SubwooferLevel Calibration UnitEqualizer Settings THX Audio SetupBGC Audio Adjust Multiplex/MonoDolby Theater-Dimensional Audyssey DSXLFE Level Audyssey Source SetupIntelliVolume SyncName Edit To correct a character Picture AdjustWide Mode*1*2 Picture Mode*1Game Mode*3*4*5 Resolution*3*5Film Mode*3*5*6 Edge Enhancement*3*5*6Audio Selector Charge Mode Listening Mode PresetVolume Setup Hardware SetupOSD Setup MiscellaneousTuner Multi ZoneAudio TV Out Auto StandbyAudio Return Channel Lip SyncFirmware Update NetworkDhcp Remote Controller Setup Lock SetupUsing the Audio Settings Dolby Volume Speaker LevelsLate Night Re-EQ Music OptimizerMusic Optimizer Re-EQConnecting the Zone Speakers to an Additional Amplifier Connecting Your Zone 2 Speakers Directly to the AV receiverMulti Zone Making Multi Zone ConnectionsOperating on the remote controller Controlling Zone 2/3 Components8RECEIVER Adjusting the Volume for Zones Adjusting the Tone and Balance of ZoneMuting Zones Using a Multiroom Kit with Zone Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Other Components Using the Onkyo Dock IPod/iPhone Playback via Onkyo DockUP-A1 Dock RI Dock Controlling Your iPod/iPhoneRandom Available buttonsPress Receiver followed by Setup Looking up for Remote Control CodeUse q/wto select a category, and then press Use q/w/e/rto select a character, and then pressEntering Remote Control Codes Resetting Remote Mode Buttons Remote Control Codes for Onkyo Components Connected via uResetting the Remote Controller Controlling Other ComponentsVCR/PVR Enter Setup Search Repeat Random Mode8SOURCE*1 Input Guide TOP MenuDeleting Acquired Commands Learning CommandsFollowing buttons cannot learn new commands RemoteMaking Macros Using Normal MacrosRunning Macros Deleting MacrosTroubleshooting PowerAudio Can’t select the Pure Audio listening mode There’s no sound with a certain signal formatSpeaker volume cannot be set as required About DTS signalsRemote Controller VideoTuner Recording UP-A1 Dock for iPod/iPhoneZone 2/3 Music Server and Internet RadioOthers USB Device PlaybackComponent Video Monitor OUT Important Note Regarding Video PlaybackUpdate procedure Firmware UpdateUpdating the Firmware via Network Before you startTroubleshooting Errors during an update via networkUpdating the Firmware via USB Using 8ON/STANDBY on the front panel, turn Press Receiver followed by Setup on Remote controllerErrors during an update via USB Select via USB and press EnterVideo Connection Formats Connection Tips and Video Signal PathOUT Audio Connection FormatsOutput Video Resolution ChartOutput Input 4K *2 1080p/24 1080i 720p 480p/576p 480i/576iUsing an RIHD-compatible TV, Player, or Recorder About p-compatible componentsOperations that can be performed with Connection Confirm the connecting and setting How to connect and setupConfirm the settings Operate with the remote controllerAbout Hdmi Supported Audio FormatsAbout Copyright Protection Network/USB Features Connecting to the NetworkNetwork Requirements USB Device Requirements Server RequirementsServer playback Remote playbackAbout Dlna Supported Audio File FormatsAmplifier Section Tuner Section SpecificationsVideo Section GeneralOthers Audio OutputsMemo 4 0 0 7 0