Mitsubishi Electronics XL650U user manual Projecting images, EN-19

Page 19

C. Projecting images

Preparation:

•Remove the lens cap.

•Turn on the power of the connected video equipment.

ENGLISH

FOCUS ring

ZOOM ring

POWER button

DVI-D (HDCP) button

COMPUTER button

POWER button

VIDEO button

COMPUTER1, 2 buttons S-VIDEO button VIDEO button

1.Confirm the POWER indicator lights up red.

•If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.

2.Press the POWER button.

•It may take about 1 minute for the lamp to light up.

•The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

•Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the lens cap.

•After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a prod- uct malfunction.

•Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after turn-on.

•The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.

•By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 35.)

3.Select an input source.

•Press the VIDEO button on the projector or the VIDEO or S-VIDEO button on the remote control that is corresponding to the terminal in use.

•The input source is switched between VIDEO and S-VIDEO at every press of the VIDEO button on the projector.

•The VIDEO and S-VIDEO buttons don’t function while the menu is being displayed.

•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

•Some images become easier to view when the setting of aspect ratio is changed. (See page 21.)

•When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO DVI- D(HDCP) terminal, press the COMPUTER button on the projector to select DVI or press the DVI-D (HDCP) button on the remote control.

•When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO IN-1/ IN-2 terminal, press the COMPUTER button on the projector or the COMPUTER 1 or COMPUTER 2 button on the remote control.

4.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

5.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)

•When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)

6.Adjust the size of the projected image by turning the ZOOM ring.

7.Adjust the focus by turning the FOCUS ring.

Repeat steps 4 to 7, if necessary.

EN-19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents XL650 XL550 EN-2 When using the projector in EuropeContents EN-4 Important safeguardsPlace of installation Do not keep using the damaged projectorDo not look into the lens when it is operating Do not unplug the power cord during op- erationInserting the batteries into the remote control Checking accessoriesPreparing your projector EN-7 OverviewControl area Terminal boardEN-8 Remote controlPreparating your projector Bottom sideEN-9 Using the remote controlOperational range of the remote control Reception angleAdjusting the projection angle Setting up your projectorSetting up the screen Basic setupRear projection Wall screenEN-11 Front projection, ceiling mountingEN-12 Setting up your projectorWhen the aspect ratio of the screen is Screen size and projection distanceViewing computer images Connecting the projector to a computerEN-13 About DDC Plugging the power cordViewing computer images EN-14EN-15 Projecting imagesAuto Position button When connecting to a notebook computerTo stop projecting AV muteViewing video images Connecting the projector to video equipmentConnecting to a video player, etc When a TV tuner or VCR is connectedProjector + DVD player or Hdtv decoder Plugging in the power cordConnecting To video equipment having a DVI-D terminal Viewing video imagesEN-19 Projecting imagesEN-20 Volume from the speakerEN-21 Setting the aspect ratioHow to change the settings When projected images are distorted to a trapezoidEN-22 Menu operationAvailable settings in the menus How to set the menusEN-23 EN-24 EN-25 EN-26 Menu operationTo sharpen or soften the projected image Sharpness Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintColor Enhancer Adjusting projected imagesTo adjust the tone of white Color Temp About color temperatureEN-29 To adjust the vertical positionLPF Progressive filter XL650U Advanced featuresSetting of the image displayed during startup or muting EN-30EN-31 Password functionTo enable the password function To cancel the password functionPicture in Picture PinP Advanced featuresEN-32 ExpandEN-33 Mouse remote controlOperation Connection Supervising and controlling by computerEN-34 Major functionsEN-35 IndicatorsNormal condition Abnormal conditionReplacing the lamp Interval of lamp replacementEN-36 EN-37 Reset of the lamp operation timeWhen removing the lamp from the ceiling-mounted projector To replace the lampCleaning of the lens MaintenanceCleaning of the air-filter Cleaning of the projector and the ventilation slotsNo image appears on the screen Problem Solution TroubleshootingEN-39 Images are not displayed correctly TroubleshootingProblem Solution EN-40Kensington Lock Images are not displayed correctly Problem SolutionOthers Problem Solution EN-41Specifications Replacement part Option/Not included in the boxEN-42 XGA85 EN-43EN-44 ConnectorsCOMPUTER/COMPONENT Video IN-1/IN-2 DVI-D Hdcp Mitsubishi Projector Contact Information
Top Page Image Contents