Mitsubishi Electronics XL650U Setting the aspect ratio, How to change the settings, EN-21

Page 21

Setting the aspect ratio

You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the input video signal.

How to change the settings:

With the remote control:

1.Press the ASPECT button.

•Every time the ASPECT button is pressed, the aspect mode changes from AUTO to 16:9, to REAL, and back to AUTO.

With the FEATURE menu:

 

 

 

 

(See page 23 for menu setting.)

 

 

 

 

 

 

opt.

 

1.

Display the FEATURE menu.

FEATURE

 

2.

Select ASPECT by pressing the ￿ or ￿ button.

 

3.

Select your desired aspect ratio by pressing the ￿ or ￿ button.

 

 

ASPECT

AUTO

 

 

 

 

 

 

 

 

 

 

When 16:9 is selected.

4.Press the ENTER button.

5.Select your desired position (CENTER, UPPER or LOWER) by pressing the ￿ or ￿ button.

To cancel the menu:

6. Press the MENU button.

Important:

•When a 16:9 image is kept displayed for a long time before displaying 4:3 image, the afterimages of the black bars may appear on the 4:3 image screen. Consult your dealer in this case.

When projected images are distorted to a trapezoid:

To correct vertical and horizontal keystone distortion, press the KEYSTONE button on the projector or the remote control to display KEYSTONE, and adjust the image by pressing the ￿, ￿, ￿, or ￿ button (or VOLUME + or - button on the remote control).

In the following cases (for front projection):

ENGLISH

Press the ￿

Press the ￿

Press the

Press the

button.

button.

￿ (or -)

￿ (or +)

 

 

button.

button.

Important:

•You can correct the vertical and horizontal keystones at the same time. However, their adjustment ranges are limited in such correction.

•When the keystone adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean a projection angle.

•The allowable range of the adjustment value in the keystone adjustment varies depending on the installation conditions.

•When the keystone adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight lines may bend in images with complicated patterns. They are not due to product malfunctions.

•Noise may appear on the screen during the keystone adjustment because of the type of the video signal being projected and the setting values of the keystone adjustment. In such cases, set the keystone adjustment values in the range where the image is displayed without noise.

•When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input signal.

EN-21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents XL650 XL550 EN-2 When using the projector in EuropeContents EN-4 Important safeguardsDo not look into the lens when it is operating Do not keep using the damaged projectorDo not unplug the power cord during op- eration Place of installationChecking accessories Inserting the batteries into the remote controlPreparing your projector Control area OverviewTerminal board EN-7Preparating your projector Remote controlBottom side EN-8Operational range of the remote control Using the remote controlReception angle EN-9Setting up the screen Setting up your projectorBasic setup Adjusting the projection angleEN-11 Wall screenFront projection, ceiling mounting Rear projectionWhen the aspect ratio of the screen is Setting up your projectorScreen size and projection distance EN-12Connecting the projector to a computer Viewing computer imagesEN-13 Viewing computer images Plugging the power cordEN-14 About DDCEN-15 Projecting imagesTo stop projecting When connecting to a notebook computerAV mute Auto Position buttonConnecting to a video player, etc Connecting the projector to video equipmentWhen a TV tuner or VCR is connected Viewing video imagesConnecting To video equipment having a DVI-D terminal Plugging in the power cordViewing video images Projector + DVD player or Hdtv decoderEN-19 Projecting imagesEN-20 Volume from the speakerHow to change the settings Setting the aspect ratioWhen projected images are distorted to a trapezoid EN-21EN-22 Menu operationHow to set the menus Available settings in the menusEN-23 EN-24 EN-25 EN-26 Menu operationTo adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessTo adjust the tone of white Color Temp Adjusting projected imagesAbout color temperature Color EnhancerTo adjust the vertical position EN-29LPF Progressive filter Setting of the image displayed during startup or muting Advanced featuresEN-30 XL650UTo enable the password function Password functionTo cancel the password function EN-31EN-32 Advanced featuresExpand Picture in Picture PinPMouse remote control EN-33Operation EN-34 Supervising and controlling by computerMajor functions ConnectionNormal condition IndicatorsAbnormal condition EN-35Interval of lamp replacement Replacing the lampEN-36 When removing the lamp from the ceiling-mounted projector Reset of the lamp operation timeTo replace the lamp EN-37Cleaning of the air-filter MaintenanceCleaning of the projector and the ventilation slots Cleaning of the lensTroubleshooting No image appears on the screen Problem SolutionEN-39 Problem Solution TroubleshootingEN-40 Images are not displayed correctlyOthers Problem Solution Images are not displayed correctly Problem SolutionEN-41 Kensington LockReplacement part Option/Not included in the box SpecificationsEN-42 XGA85 EN-43Connectors EN-44COMPUTER/COMPONENT Video IN-1/IN-2 DVI-D Hdcp Mitsubishi Projector Contact Information
Top Page Image Contents