Mitsubishi Electronics XL650U user manual Advanced features, EN-30

Page 30

Advanced features

Setting of the image displayed during startup or muting

You can display your desired image as the startup screen (or splash screen). Using the menu, you can also use such image as a background that is displayed while the video is muted or no signal is supplied.

Important:

You can’t set IMAGE CAPTURE when PASSWORD FUNCTION in the FEATURE menu has been set to SPLASH ID SCREEN to enable the password lock.

You can’t set IMAGE CAPTURE when the compo- nent video signal is inputted.

Setting procedure

1.Press the COMPUTER button to select the image supplied to the COMPUTER/COMPONENT VIDEO IN terminal.

2.Display your desired image.

3.Display the INSTALLATION menu.

4.Select IMAGE CAPTURE by pressing the ￿ or ￿ button.

5.Press the ENTER button.

• The setting menu will be displayed.

opt.

 

INSTALLATION

 

CUSTOM IMAGE CAPTURE

BACK COLOR

GRAY

SIZE

x1

CAPTURE

GO

Set the background color

(Set the background color only when you set the im- age size to x1 or x2.)

6.Select BACK COLOR by pressing the ￿ or ￿ but- ton.

7.Select your desired color for the background (GRAY,

RED, GREEN, BLUE, BLACK, WHITE, RED50%, GREEN50%, or BLUE50%) by pressing the ￿ or ￿ button.

Set the image size

8.Select SIZE by pressing the ￿ or ￿ button.

9.Select x1, x2, or FULL by pressing the ￿ or ￿ but- ton.

x1

x2

FULL

Capture the image

10.Select CAPTURE by pressing the ￿ or ￿ button. 11.Press the ENTER button.

A red frame appears. (The size of the red frame is 320x240 pixels.)

XL650U

CAPTURE : ENTER X2

CANCEL : MENU

CAPTURE : ENTER + ENTER

CANCEL : MENU

12.Adjust the size of the image to be captured so that such image stays within the red frame.

Press the ￿, ￿, ￿ or ￿ button to move the red frame.

You can’t move the red frame outside the screen.

XL650U

CAPTURE : ENTER X2

CANCEL : MENU

13.Press the ENTER button twice.

Image capture will start.

Press the MENU button to cancel the procedure.

Capturing Logo !

LVP-XD300

When the image capture completes, the cap- tured image will be displayed for three seconds.

Important:

You can’t change the new startup screen back to the original startup screen. (Even when you select RESET ALL in the FEATURE menu, the factory default screen isn’t available any longer.) When you want to change the startup screen again, capture another image.

The captured image will be displayed from the next startup. If the captured image isn’t displayed, make sure that the setting of SPLASH SCREEN in the INSTALLATION menu isn’t OFF. (See page 24.)

To display the captured image while the video is muted, set MUTE MODE in the INSTALLATION menu to IMAGE. (See page 24.)

When BACK COLOR in the INSTALLATION menu is set to IMAGE, the captured image will be displayed while no signal is supplied.

Some images can’t be captured correctly because of their signal type.

EN-30

Image 30
Contents XL650 XL550 When using the projector in Europe EN-2Contents Important safeguards EN-4Do not unplug the power cord during op- eration Do not keep using the damaged projectorDo not look into the lens when it is operating Place of installationChecking accessories Inserting the batteries into the remote controlPreparing your projector Terminal board OverviewControl area EN-7Bottom side Remote controlPreparating your projector EN-8Reception angle Using the remote controlOperational range of the remote control EN-9Basic setup Setting up your projectorSetting up the screen Adjusting the projection angleFront projection, ceiling mounting Wall screenEN-11 Rear projectionScreen size and projection distance Setting up your projectorWhen the aspect ratio of the screen is EN-12Connecting the projector to a computer Viewing computer imagesEN-13 EN-14 Plugging the power cordViewing computer images About DDCProjecting images EN-15AV mute When connecting to a notebook computerTo stop projecting Auto Position buttonWhen a TV tuner or VCR is connected Connecting the projector to video equipmentConnecting to a video player, etc Viewing video imagesViewing video images Plugging in the power cordConnecting To video equipment having a DVI-D terminal Projector + DVD player or Hdtv decoderProjecting images EN-19Volume from the speaker EN-20When projected images are distorted to a trapezoid Setting the aspect ratioHow to change the settings EN-21Menu operation EN-22How to set the menus Available settings in the menusEN-23 EN-24 EN-25 Menu operation EN-26To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerTo adjust the vertical position EN-29LPF Progressive filter EN-30 Advanced featuresSetting of the image displayed during startup or muting XL650UTo cancel the password function Password functionTo enable the password function EN-31Expand Advanced featuresEN-32 Picture in Picture PinPMouse remote control EN-33Operation Major functions Supervising and controlling by computerEN-34 ConnectionAbnormal condition IndicatorsNormal condition EN-35Interval of lamp replacement Replacing the lampEN-36 To replace the lamp Reset of the lamp operation timeWhen removing the lamp from the ceiling-mounted projector EN-37Cleaning of the projector and the ventilation slots MaintenanceCleaning of the air-filter Cleaning of the lensTroubleshooting No image appears on the screen Problem SolutionEN-39 EN-40 TroubleshootingProblem Solution Images are not displayed correctlyEN-41 Images are not displayed correctly Problem SolutionOthers Problem Solution Kensington LockReplacement part Option/Not included in the box SpecificationsEN-42 EN-43 XGA85Connectors EN-44COMPUTER/COMPONENT Video IN-1/IN-2 DVI-D Hdcp Mitsubishi Projector Contact Information