Mitsubishi Electronics XL650U user manual Indicators, Normal condition, Abnormal condition, EN-35

Page 35

Indicators

This projector has 2 indicators, each of which shows the operation condition of the projector.

The following offer solutions to possible problems. If these problems persist, turn the projector off and consult your dealer.

POWER indicator

STATUS indicator

Normal condition

POWER

STATUS

CONDITION

NOTE

Steady

Off

Stand-by

 

 

 

red

 

 

 

Steady

Blinking

Lamp stand-by (about 1 minute)

The POWER button cannot be used to

 

switch between on and off.

green

green

 

Steady

Steady

The power is on. (Normal condition)

 

 

 

green

green

 

 

Abnormal condition

POWER

STATUS

CONDITION

POSSIBLE SOLUTION

 

 

 

 

 

 

 

 

 

 

Abnormal temperature

 

Steady

 

 

 

 

 

• The ventilation grilles are clogged with dust or dirt.

• Clean the ventilation grilles.

green

 

 

 

 

 

• The room temperature is high.

• Relocate the projector to a cooler place.

or

 

 

 

 

 

 

 

Blinking orange

 

 

Steady red

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The protection circuit is working or the lamp is in an

• Wait until the STATUS indicator goes out,

Steady red

 

 

 

 

 

abnormal condition.

then press the POWER button.

 

 

 

 

 

Blinking green

 

• If the above solution is not effective,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

replace the lamp.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Lamp operation time warning. (Total lamp operation time

Replace the lamp.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Steady

Blinking green/red

reached 3750 hours*1 while the power was on.)

Change with a new lamp if this problem

green

 

 

 

 

 

 

recurs.

 

 

 

 

 

 

 

 

 

 

Lamp operation time warning. (Total lamp operation time

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Steady red

Blinking red

reached 3750 hours*1 while the power was off.)

 

 

 

 

 

 

 

 

 

 

 

Lamp operation time warning. (Total lamp operation time

 

Steady red

Steady red

reached 5000 hours*1*2 while the power was off.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Off

The lamp cover isn’t closed.

Close the cover correctly.

 

 

 

 

 

 

Blinking

 

 

 

 

 

 

 

 

 

 

green/red

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Abnormal.

Contact your dealer.

Steady

or

Blinking

green/red

Blinking

*1 Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be shorted.

*2 Duration when LAMP MODE is set to STANDARD, this duration will be shorted up to 2000 hours.

ENGLISH

EN-35

Image 35
Contents XL650 XL550 EN-2 When using the projector in EuropeContents EN-4 Important safeguardsPlace of installation Do not keep using the damaged projectorDo not look into the lens when it is operating Do not unplug the power cord during op- erationPreparing your projector Checking accessoriesInserting the batteries into the remote control EN-7 OverviewControl area Terminal boardEN-8 Remote controlPreparating your projector Bottom sideEN-9 Using the remote controlOperational range of the remote control Reception angleAdjusting the projection angle Setting up your projectorSetting up the screen Basic setupRear projection Wall screenEN-11 Front projection, ceiling mountingEN-12 Setting up your projectorWhen the aspect ratio of the screen is Screen size and projection distanceEN-13 Connecting the projector to a computerViewing computer images About DDC Plugging the power cordViewing computer images EN-14EN-15 Projecting imagesAuto Position button When connecting to a notebook computerTo stop projecting AV muteViewing video images Connecting the projector to video equipmentConnecting to a video player, etc When a TV tuner or VCR is connectedProjector + DVD player or Hdtv decoder Plugging in the power cordConnecting To video equipment having a DVI-D terminal Viewing video imagesEN-19 Projecting imagesEN-20 Volume from the speakerEN-21 Setting the aspect ratioHow to change the settings When projected images are distorted to a trapezoidEN-22 Menu operationEN-23 How to set the menusAvailable settings in the menus EN-24 EN-25 EN-26 Menu operationTo sharpen or soften the projected image Sharpness Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintColor Enhancer Adjusting projected imagesTo adjust the tone of white Color Temp About color temperatureLPF Progressive filter To adjust the vertical positionEN-29 XL650U Advanced featuresSetting of the image displayed during startup or muting EN-30EN-31 Password functionTo enable the password function To cancel the password functionPicture in Picture PinP Advanced featuresEN-32 ExpandOperation Mouse remote controlEN-33 Connection Supervising and controlling by computerEN-34 Major functionsEN-35 IndicatorsNormal condition Abnormal conditionEN-36 Interval of lamp replacementReplacing the lamp EN-37 Reset of the lamp operation timeWhen removing the lamp from the ceiling-mounted projector To replace the lampCleaning of the lens MaintenanceCleaning of the air-filter Cleaning of the projector and the ventilation slotsEN-39 TroubleshootingNo image appears on the screen Problem Solution Images are not displayed correctly TroubleshootingProblem Solution EN-40Kensington Lock Images are not displayed correctly Problem SolutionOthers Problem Solution EN-41EN-42 Replacement part Option/Not included in the boxSpecifications XGA85 EN-43COMPUTER/COMPONENT Video IN-1/IN-2 DVI-D Hdcp ConnectorsEN-44 Mitsubishi Projector Contact Information