Mitsubishi Electronics XL7000U user manual How to change the settings With the remote control

Page 29

Viewing video images (continued)

Setting the aspect ratio

You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according to the type of the input video signal.

How to change the settings:

With the remote control:

1.Press the ASPECT button.

t &WFSZUJNFUIF"41&$5CVUUPOJTQSFTTFEUIFBTQFDUNPEFDIBOHFTGSPN/03."-UPUP'6--BOE back to NORMAL.

-NORMAL:

Select to change the aspect ratio automatically depending on the input signal. (Select this option for normal use.)

-16:9:

Select to expand squeezed (or horizontally compressed) images such as DVD images to 16:9.

-FULL:

Select to project images in full size (1024 x 768 pixels) irrespective of type of input signal.

With the FEATURE menu: (See page 31 for menu setting.)

1.Display the FEATURE menu.

2.Select ASPECT by pressing the or button.

3.Select your desired aspect ratio by pressing the or button.

When 16:9 is selected with the FEATURE menu, you can make further settings using the following procedures.

opt.

FEATURE

 

 

ASPECT

NORMAL

 

 

PROJECTOR ID

ALL

 

 

 

 

 

 

4. Press the ENTER button.

 

 

5. Select an item you want to set by pressing the or button and select a

opt.

 

 

 

setting by pressing the or button.

FEATURE

 

t

104*5*0/

 

ASPECT – 16:9

 

 

You can select the image display position within the screen from

 

 

POSITION

CENTER

 

UPPER, CENTER, and LOWER.

 

MODE

ALL SIGNALS

t

.0%&

 

 

 

You can select whether or not to display signals at 16:9 depending on their type.

 

-ALL SIGNALS:

All signals are always displayed at 16:9 irrespective of their type.

-VIDEO ONLY:

Signals supplied from video devices only are displayed at 16:9.

To cancel the menu:

6. Press the MENU button.

Important:

t 8IFOBJNBHFJTLFQUEJTQMBZFEGPSBMPOHUJNFCFGPSFEJTQMBZJOHJNBHFUIFBGUFSJNBHFTPGUIFCMBDLCBST may appear on the 4:3 image screen. (See page 59.)

EN-29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents XL7000 Risk of Electric Shock Do not Open Contents Important safeguards Do not keep using the damaged projector Important safeguardsInserting the batteries into the remote control Checking accessoriesRemoving the batteries from the remote control Preparing your projectorControl area Preparing your projectorOverview Bottom side IndicatorsRemote control Operational range of the remote control Using the remote controlUsing the wired remote control Reception angleSetting the ID number of the remote control Using the remote controlSetting by the remote control alone Setting by using the projectorBefore setting up Setting up your projectorSetting up the screen Screen size and projection distanceSetup adjustment Setting up your projectorAdjusting the position of the projected image Changing the Auto Power OFF settingSetting Image Reverse Setting High Altitude ModeWhen fine streaks are seen on projected images When the projected image is distortedAdjustment using the Cornerstone mode Adjustment using the Keystone modeKeystone → Reset → Keystone Keystone menuLower RIGHT, Lower LEFT, Upper RIGHT, or Upper Left menu Adjustment using the Curved modeARC menu HORIZ. Origin or VERT. Origin menuBe corrected by the CORNERSTONE-mode adjustment Adjusting the origin to the vertical arcRear projection Front projection, ceiling mounting *OBEVTUZPSIVNJEQMBDF  /FBSBIFBUFSViewing computer images Connecting the projector to a computerViewing computer images Plugging the power cordAbout DDC For monitor connectionInstalling the terminal cover Projecting images Confirm the Power indicator lights up red 3FNPWFUIFMFOTDBQ Select an input source $PWFSUIFMFOTXJUIUIFMFOTDBQUPQSPUFDUJUGSPNEVTU Direct Power OFFTo stop projecting Setting of the resolution When connecting to a notebook computerExample of the setting procedure for external output Blanking the screen temporarily BlankConnecting to a video player, etc Connecting the projector to video equipmentWhen a TV tuner or VCR is connected Viewing video imagesProjector + DVD player or Hdtv decoder Viewing video imagesConnection for video equipment having a DVI-D terminal Plugging in the power cordEN-27 Setting the aspect ratio Volume from the speakerWith the Feature menu See page 31 for menu setting How to change the settings With the remote controlMenu operation Image menu Installation menu Feature menuSignal menu Network menu Information menu Press the  or  button to select an item to adjust How to set the menusMenu operation Press the  or  button to select a menu to useAuto Image menuEnhanced SeeStandby Mode Standard Setting Function Lamp Mode StandardAuto Power on On / OFF Auto Power OFFCinema Mode Auto Menu Access Splash ID Screen Menu PositionHigh Altitude Mode Standard Aspect NormalVideo Signal Auto / Ntsc / PAL / Secam Setting Function Advanced Menu EnterSetup Auto Reset ALLSignal menu Network Password Enter Setting Function Projector NameIP Config Enter Default GatewayDescription ResolutionLamp Time LOW Serial NumberTo adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To adjust the tone of white Color TempColor Enhancer Adjusting projected imagesAbout color temperature Adjusting the tone of each color NCM Adjusting the fineness of the image Super ResolutionSelect an item you want to set using  or  button Select NCM by pressing the  or  buttonYES How to adjust the computer imageTo adjust the horizontal position Simple method to adjust the image positionTo adjust the vertical position LPF Progressive filterSetting Projector Name Initial network settingsNetwork Password Settings Enabling or disabling the network certificationIP Settings Initial network settingsSetting or Clearing Dhcp IP Address SettingsSubnet Mask Settings Setting the control systemDefault Gateway Settings Saving IP Config SettingsHow to Use Network Function Initialization of Network SettingsGlossary DhcpChanging the image displayed at the startup Advanced featuresSetting procedure Password function Advanced featuresTo enable the password function To cancel the password functionFreeze Picture in Picture PinPMagnifying the displayed image Major functions Connection PJLink supported commandsReplacing the lamp Interval of lamp replacementTo replace the lamp Reset of the lamp operation timeReplacing the lamp When removing the lamp from the ceiling-mounted projector Cleaning of the projector and the ventilation slots MaintenanceCleaning of the lens Cleaning of the filterMounting the lens option lens Replacing the lensRemoving the lens No image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly TroubleshootingProblem Solution $IFDLUIBUUIFWPMVNFJTOUTFUUPMPX Images are not displayed correctly Problem SolutionOthers Problem Solution 3FTFUUIFMBNQPQFSBUJOHUJNF 4FFQBHF FOCUS/ZOOMJUUIFMBNQDPWFSTFDVSFMZ 4FFQBHF Power Status Filter Condition Possible Solution IndicatorsPower Status Filter Condition Specifications Replacement part option/not included in the boxXGA85 SpecificationsDimension drawings unit mm ConnectorsComposite Sync Hdmi SerialWith short throw zoom lens OL-XL7100SZ Specification of the attached lensWith long throw zoom lens OL-XL7100LZ With tele throw zoom lens OL-XL7100TZProjection With rear projection short throw OL-XL7100FRMitsubishi Electric Corporation
Top Page Image Contents