Onkyo TX-SR674/674E Connecting Antenna, Connecting the Indoor FM Antenna, Other models

Page 21

Connecting the AV Receiver—Continued

Connecting Antenna

This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

AM antenna push terminals

FM antenna connector

Connecting the Indoor FM Antenna

The supplied indoor FM antenna is for indoor use only.

1 Attach the FM antenna, as shown.

■North American models

FM 75

Insert the plug fully into the jack.

■Other models

FM 75

Insert the plug fully into the jack.

Once your AV receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.

2 Use thumbtacks or something similar to ﬁx the FM antenna into position.

Thumbtacks, etc.

Caution: Be careful that you don’t injure yourself when using thumbtacks.

If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out- door FM antenna instead (see page 22).

Connecting the AM Loop Antenna

The supplied indoor AM loop antenna is for indoor use only.

1 Assemble the AM loop antenna, inserting the tabs into the base, as shown.

2 Connect both wires of the AM loop antenna to the AM push terminals, as shown.

(The antenna’s wires are not polarity sensitive, so they can be connected either way around.) Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.

Push

Insert wire

Release

Once your AV receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.

Keep the antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commer- cially available outdoor AM antenna (see page 22).

21

Image 21

Contents TX-SR604/604E TX-SR8460 TX-SR674/674E TX-SR8467 Avis Important Safety InstructionsPower PrecautionsFor models having a power cord with a polarized plug FCC Information for UserPrecautions Supplied AccessoriesMake sure you have the following accessories Speaker cable labels Power-plug adapterFeatures TX-SR674/674E and TX-SR8467 OnlyTX-SR604/604E and TX-SR8460 Only Table of Contents Front Panel Front & Rear PanelsFront & Rear Panels Display Digital Optical in 1, 2, 3 and OUT Rear PanelXM antenna on North American models Hdmi in 1, 2, and OUTZone 2 Line OUT Remote Controller Installing the BatteriesAiming the Remote Controller Remote Controller Using the Remote ControllerRECEIVER/TAPE Mode Buttons used when the Tuner input is selected Remote Mode buttonsButtons used when the Tape input is selected Zone 2 buttonDVD Mode To select the input source, press CD/MD/CDR/HDD ModeDISC/ALBUM +/- button Arrow / and Enter buttonsEnjoying Home Theater About Home TheaterAbout AV Connections Connecting the AV ReceiverOptical Digital Jacks AV Connection Color CodingConnecting Your Speakers Connecting the AV ReceiverConnecting the Speaker Cables Speaker Connection PrecautionsRead the following before connecting your speakers Strip about 5/8 15 mmConnecting the Indoor FM Antenna Connecting AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shown North American modelsConnecting an Outdoor FM Antenna Connecting an Outdoor AM AntennaUsing a TV/FM Antenna Splitter Which Connections Should I Use? Connecting Both Audio & VideoVideo Connection Formats Audio Connection FormatsVideo Connection Connecting Your TV or ProjectorAudio Connection HintConnecting a DVD Player DVD player Hooking Up the Multichannel DVD InputDVD recorder Connecting a VCR or DVD Recorder for PlaybackConnecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device About Hdmi Connecting Components with HdmiSupported Audio Formats About Copyright ProtectionAudio Signal Flow Chart Video Signal Flow ChartMaking Hdmi Connections TX-SR604/604E, TX-SR8460CD Player or Turntable MM with Built-in Phono Preamp Step Connecting a CD Player or TurntableConnect your HDD-compatible component’s analog Connecting a HDD-compatible ComponentAudio output jacks and video output jack to the AV Receiver’s Video 3 in L/R jacks and Video 3 JacksConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Connecting the Power Cord of Another Component Connecting Onkyo ComponentsAuto Power On/Standby Remote ControlDo the automatic speaker setup-this is essential Connecting the Power CordTurning On the AV Receiver Turning On and StandbyFirst Time Setup Automatic Speaker Setup Audyssey2EQMeasurement Points First Time Setup Connect the setup microphone to the Setup MIC jackPress Enter Disconnect the speaker setup When the calculations are comFollowing screen appears Plete, the following screenSpeaker Detect Errors Error MessagesReviewing the Results Ambient noise is too highChanging the Speaker Settings Manually Using a Powered SubwooferPress the Return button to return to the previous menu About the Onscreen Setup Menus SubmenusMain menu Digital Input Video Input Hdmi Video SetupComponent Video Setup Setup menu closesMain menu appears onscreen Minimum Speaker Impedance not North American models Changing the Input DisplayAM Frequency Step Setup on some models TV Format Setup Not North American modelsHardware Setup menu appears You must specify the TV system used in your areaSelecting the Input Source Basic OperationsStart playback on the source component Video OUT, Hdmi OUT or Monitor OUTAdjusting the Bass & Treble Using the Multichannel DVD InputBasic Operations Displaying Source InformationSetting the Display Brightness Using the Sleep TimerUsing Headphones Muting the AV ReceiverTuning into Radio Stations Using the TunerListening to the Radio Listening to the RadioSelecting Presets Presetting AM/FM Stations XM ChannelsDeleting Presets Listening to the RadioUsing RDS European models only What is RDS?RDS Program Types PTY Displaying Radio Text RT Listening to Trafﬁc News TPFinding Stations by Type PTY Listening to XM Satellite Radio North American models only Connecting the XM Passport SystemImportant XM Radio Information About XM RadioSetting the Satellite Radio Mode Signing Up for XM Satellite RadioSelecting XM Satellite Radio Selecting XM Radio Channels Channel Search mode select any channelThere are three ways to select XM radio channels Receiver button ﬂashesDisplaying XM Radio Information XM Radio Messages TER signal strength bar is asPositioning the XM Passport System Long as possibleSelecting with the Remote Controller Using the Listening ModesSelecting Listening Modes Selecting on the AV ReceiverDVD Using the Listening ModesAbout the Listening Modes Onkyo Original DSP Modes Use this mode with any stereo movie e.g., TV, DVD, VHSRecording AV RecordingRecording Separate AV Sources Using the Late Night Function Dolby Digital only Using the CinemaFILTERAdjusting Individual Speaker Levels Advanced OperationsAdvanced Setup Speaker SetupSpeaker Conﬁg menu appears Advanced Setup Low-Pass Filter for the LFE ChannelDouble Bass Tance, and then press Enter Speaker DistanceSpeaker Distance menu appears Buttons to select 2. Speaker DisSpeaker Level Calibration Repeat until the volumeTest tone from each speaker Is the sameSettings, and then press Equalizer SettingEqualizer Settings menu appears Buttons to select 4. EqualizerAudio Adjust Functions Multichannel DVD Input SettingsWhen you’ve ﬁnished, press SW Input SensitivityPL IIx Music Mode Settings Input Channel SettingsNeo6 Music Mode Setting Dolby Digital EX Input Signal SettingAssigning Listening Modes to Input Sources Tons on the remote controller toUse the Input Selector but Select the input source that youVolume Setup/OSD Setup IntelliVolumeUse the Up and Down Buttons to select a. IntelliVolume Lowed by the Setup button. The main menu appears onscreenHdmi Audio Out Changing the AV Receiver’s IDDigital Input Signal Formats Lock SetupPress and hold the AV receiver’s Digi TAL Input button for about 3 secondsCorrecting Sound and Picture Sync Changing the Remote Controller’s IDPress the Receiver and the Cine Fltr at the same timeUsing a Receiver/Integrated Amp in Zone Connecting ZoneUsing Only Speakers in Zone ZoneButtons to select Powered Zone Setting the Powered ZoneUsing Zone Controlling Zone 2 with the Remote ControllerControlling Zone 2 from the AV receiver Adjusting the Volume for Zone Using the Remote Control in ZoneUsing a Multiroom Kit with Zone Using a Multiroom Kit with a CabinetControlling Other Components Entering Remote Control CodesResetting Remote Mode Buttons Remote Control Codes for Onkyo Components Connected viaResetting the Remote Controller Controlling Other ComponentsCH + TV VOLAmpliﬁer Section SpeciﬁcationsVideo Section Tuner SectionTroubleshooting Troubleshooting There’s no picture from a source connected to an Hdmi Remote controller doesn’t workOnscreen menus don’t appear Immediate display does not appearSpeaker volume cannot be set as required Sound changes when I connect my head- phonesThere’s no sound Speaker distance cannot be set as requiredMemo Onkyo Europe UK Office Onkyo Europe Electronics GmbH