Onkyo TX-SR674/674E, TX-SR604/604E instruction manual Changing the Input Display

Page 47

First Time Setup—Continued

Changing the Input Display

If you connect an -capable Onkyo MiniDisc recorder, CD recorder, or next generation HDD-compat- ible component to the TAPE IN/OUT or VIDEO 3 IN

jacks, for to work properly, you must change this setting.

This setting can only be changed on the AV receiver.

1, 2

1, 2

iPod photo: If you’re using an iPod photo with the DS-A1 Remote Interactive Dock, connect the DS-A1 to the VIDEO 3 IN jacks.

1

Press the [TAPE] or [VIDEO 3]

 

TAPE

 

input selector button so that

 

“TAPE” or “VIDEO 3” appears on

 

the display.

 

VIDEO 3

Minimum Speaker Impedance (not North American models)

If you change this setting, you must run the automatic speaker setup again (see page 38).

If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms.

Note:

Before you change this setting, turn down the volume.

1

RECEIVER

Press the [RECEIVER] button,

followed by the [SETUP] button.

 

 

 

 

The main menu appears onscreen.

SETUP

 

 

2

 

Use the Up and Down [ ]/[ ]

 

 

buttons to select “8. Hardware

 

 

Setup,” and then press [ENTER].

 

 

The Hardware Setup menu appears.

 

 

8.Hardware Setup

 

 

 

------------------------

 

 

a.SP Impedance :6ohms

 

 

b.PoweredZone2:NotAct

 

 

c.TV Format

:Auto

 

 

d.AM Freq. Step: 9kHz

 

 

e.Remote ID

:1

 

 

f.HDMI Audio Out :Off

 

 

g.SW Input Sensitivity

 

 

 

: 0dB

2 TAPE

VIDEO 3

Press and hold down the [TAPE] or [VIDEO 3] input selector but- ton (about 3 seconds) to change the setting.

Repeat this step to select MD, CDR, or HDD.

For the TAPE input selector, the setting changes in this order:

TAPE MD CDR HDD

For the VIDEO 3 input selector, the set- ting changes in this order:

VIDEO 3 HDD

3

Use the Up and Down [ ]/[ ]

buttons to select “SP Imped- ance,” and then use the Left and Right []/[ ] buttons to select:

4 ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6.

6 ohms: Select if the impedances of all speakers are between 6 and 16 ohms.

Note:

HDD can be selected for the TAPE input selector or VIDEO 3 input selector, but not both at the same time.

4

Press the [SETUP] button.

 

 

Setup closes.

SETUP

Note:

This procedure can also be performed on the AV receiver by using its [SETUP] button, arrow buttons, and [ENTER] button.

47

Image 47
Contents TX-SR604/604E TX-SR8460 TX-SR674/674E TX-SR8467 Avis Important Safety InstructionsFCC Information for User PrecautionsPower For models having a power cord with a polarized plugSpeaker cable labels Power-plug adapter Supplied AccessoriesPrecautions Make sure you have the following accessoriesTX-SR604/604E and TX-SR8460 Only FeaturesTX-SR674/674E and TX-SR8467 Only Table of Contents Front Panel Front & Rear PanelsFront & Rear Panels Display Hdmi in 1, 2, and OUT Rear PanelDigital Optical in 1, 2, 3 and OUT XM antenna on North American modelsZone 2 Line OUT Aiming the Remote Controller Remote ControllerInstalling the Batteries RECEIVER/TAPE Mode Remote ControllerUsing the Remote Controller Zone 2 button Remote Mode buttonsButtons used when the Tuner input is selected Buttons used when the Tape input is selectedDVD Mode Arrow / and Enter buttons CD/MD/CDR/HDD ModeTo select the input source, press DISC/ALBUM +/- buttonEnjoying Home Theater About Home TheaterAV Connection Color Coding Connecting the AV ReceiverAbout AV Connections Optical Digital JacksConnecting Your Speakers Connecting the AV ReceiverStrip about 5/8 15 mm Speaker Connection PrecautionsConnecting the Speaker Cables Read the following before connecting your speakersAttach the FM antenna, as shown North American models Connecting AntennaConnecting the Indoor FM Antenna Connecting the AM Loop AntennaUsing a TV/FM Antenna Splitter Connecting an Outdoor FM AntennaConnecting an Outdoor AM Antenna Audio Connection Formats Connecting Both Audio & VideoWhich Connections Should I Use? Video Connection FormatsHint Connecting Your TV or ProjectorVideo Connection Audio ConnectionConnecting a DVD Player DVD player Hooking Up the Multichannel DVD InputDVD recorder Connecting a VCR or DVD Recorder for PlaybackConnecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device About Copyright Protection Connecting Components with HdmiAbout Hdmi Supported Audio FormatsTX-SR604/604E, TX-SR8460 Video Signal Flow ChartAudio Signal Flow Chart Making Hdmi ConnectionsCD Player or Turntable MM with Built-in Phono Preamp Step Connecting a CD Player or TurntableReceiver’s Video 3 in L/R jacks and Video 3 Jacks Connecting a HDD-compatible ComponentConnect your HDD-compatible component’s analog Audio output jacks and video output jack to the AVConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Remote Control Connecting Onkyo ComponentsConnecting the Power Cord of Another Component Auto Power On/StandbyTurning On and Standby Connecting the Power CordDo the automatic speaker setup-this is essential Turning On the AV ReceiverMeasurement Points First Time SetupAutomatic Speaker Setup Audyssey2EQ Press Enter First Time SetupConnect the setup microphone to the Setup MIC jack Plete, the following screen When the calculations are comDisconnect the speaker setup Following screen appearsAmbient noise is too high Error MessagesSpeaker Detect Errors Reviewing the ResultsPress the Return button to return to the previous menu Changing the Speaker Settings ManuallyUsing a Powered Subwoofer Main menu About the Onscreen Setup MenusSubmenus Digital Input Video Input Hdmi Video SetupMain menu appears onscreen Component Video SetupSetup menu closes Minimum Speaker Impedance not North American models Changing the Input DisplayYou must specify the TV system used in your area TV Format Setup Not North American modelsAM Frequency Step Setup on some models Hardware Setup menu appearsVideo OUT, Hdmi OUT or Monitor OUT Basic OperationsSelecting the Input Source Start playback on the source componentDisplaying Source Information Using the Multichannel DVD InputAdjusting the Bass & Treble Basic OperationsMuting the AV Receiver Using the Sleep TimerSetting the Display Brightness Using HeadphonesListening to the Radio Using the TunerTuning into Radio Stations Listening to the RadioListening to the Radio Presetting AM/FM Stations XM ChannelsSelecting Presets Deleting PresetsRDS Program Types PTY Using RDS European models onlyWhat is RDS? Finding Stations by Type PTY Displaying Radio Text RTListening to Traffic News TP About XM Radio Connecting the XM Passport SystemListening to XM Satellite Radio North American models only Important XM Radio InformationSelecting XM Satellite Radio Setting the Satellite Radio ModeSigning Up for XM Satellite Radio Receiver button flashes Channel Search mode select any channelSelecting XM Radio Channels There are three ways to select XM radio channelsDisplaying XM Radio Information Long as possible TER signal strength bar is asXM Radio Messages Positioning the XM Passport SystemSelecting on the AV Receiver Using the Listening ModesSelecting with the Remote Controller Selecting Listening ModesDVD Using the Listening ModesAbout the Listening Modes Onkyo Original DSP Modes Use this mode with any stereo movie e.g., TV, DVD, VHSRecording Separate AV Sources RecordingAV Recording Advanced Operations Using the CinemaFILTERUsing the Late Night Function Dolby Digital only Adjusting Individual Speaker LevelsSpeaker Config menu appears Advanced SetupSpeaker Setup Double Bass Advanced SetupLow-Pass Filter for the LFE Channel Buttons to select 2. Speaker Dis Speaker DistanceTance, and then press Enter Speaker Distance menu appearsIs the same Repeat until the volumeSpeaker Level Calibration Test tone from each speakerButtons to select 4. Equalizer Equalizer SettingSettings, and then press Equalizer Settings menu appearsSW Input Sensitivity Multichannel DVD Input SettingsAudio Adjust Functions When you’ve finished, pressDolby Digital EX Input Signal Setting Input Channel SettingsPL IIx Music Mode Settings Neo6 Music Mode SettingSelect the input source that you Tons on the remote controller toAssigning Listening Modes to Input Sources Use the Input Selector butLowed by the Setup button. The main menu appears onscreen IntelliVolumeVolume Setup/OSD Setup Use the Up and Down Buttons to select a. IntelliVolumeHdmi Audio Out Changing the AV Receiver’s IDTAL Input button for about 3 seconds Lock SetupDigital Input Signal Formats Press and hold the AV receiver’s DigiFltr at the same time Changing the Remote Controller’s IDCorrecting Sound and Picture Sync Press the Receiver and the CineZone Connecting ZoneUsing a Receiver/Integrated Amp in Zone Using Only Speakers in ZoneButtons to select Powered Zone Setting the Powered ZoneControlling Zone 2 from the AV receiver Using ZoneControlling Zone 2 with the Remote Controller Using a Multiroom Kit with a Cabinet Using the Remote Control in ZoneAdjusting the Volume for Zone Using a Multiroom Kit with ZoneControlling Other Components Entering Remote Control CodesControlling Other Components Remote Control Codes for Onkyo Components Connected viaResetting Remote Mode Buttons Resetting the Remote ControllerCH + TV VOLTuner Section SpecificationsAmplifier Section Video SectionTroubleshooting Troubleshooting Immediate display does not appear Remote controller doesn’t workThere’s no picture from a source connected to an Hdmi Onscreen menus don’t appearSpeaker distance cannot be set as required Sound changes when I connect my head- phonesSpeaker volume cannot be set as required There’s no soundMemo Onkyo Europe UK Office Onkyo Europe Electronics GmbH