Onkyo TX-SR604/604E Using the Remote Control in Zone, Adjusting the Volume for Zone

Page 82

Zone 2—Continued

Adjusting the Volume for Zone 2

ZONE 2 LEVEL ,

Using the Remote Control in Zone 2

To use the remote controller to control the AV receiver from Zone 2, you’ll need one of the following commer- cially available multiroom remote control kits:

Multiroom Kits are made by Niles and Xantech. These kits can also be used when the AV receiver is not in line of sight of the remote controller, for example, when it’s installed inside a cabinet.

Using a Multiroom Kit with Zone 2

Remote

controller

ZONE2

On the remote controller, press the [ZONE 2] button, and then use the [LEVEL–] and [LEVEL+] buttons.

In the following diagram, an IR receiver picks up the infrared signals from the remote controller in Zone 2 and feeds them to the AV receiver in the main room via the connecting block.

LEVEL- LEVEL+

AV receiver

On the AV receiver, use the ZONE 2 LEVEL []/[ ] buttons.

Connecting block

Main room

IR receiver

Remote controller

Zone 2

If your Zone 2 speakers are connected to an amp in Zone 2, use its volume control to adjust the volume.

Signal flow

Connect the miniplug cable from the connecting block to the AV receiver’s IR IN jack as shown below.

To Mute Zone 2:

Press the remote controller’s [ZONE 2] button, followed by the [MUTING] button. To unmute Zone 2, press the remote controller’s [ZONE 2] button again, followed by the [MUTING] button, or adjust the volume for Zone 2.

Notes:

Only analog input sources are output by the ZONE 2 LINE OUT and ZONE 2 SPEAKERS terminals. Dig- ital input sources are not output. If no sound is heard when an input source is selected, check if it’s con- nected to an analog input.

While Zone 2 is being used, listening modes that need surround back speakers (i.e., Dolby Digital EX and DTS-ES) are unavailable.

While Zone 2 is on, functions will not work.

You can’t select different radio stations for Zone 2 and the main room. For example, if you have an FM sta- tion for the main room, that station will also be used in Zone 2.

from the connecting block

Miniplug cable

Using a Multiroom Kit with a Cabinet

In the following diagram, an IR receiver picks up the infrared signals from the remote controller and feeds them to the AV receiver in the cabinet via the connecting block.

IR receiver Connecting

block

IR IN

Inside

 

cabinet

Remote controller

Signal flow

 

82

Image 82
Contents TX-SR604/604E TX-SR8460 TX-SR674/674E TX-SR8467 Important Safety Instructions AvisFor models having a power cord with a polarized plug PrecautionsPower FCC Information for UserMake sure you have the following accessories Supplied AccessoriesPrecautions Speaker cable labels Power-plug adapterTX-SR674/674E and TX-SR8467 Only FeaturesTX-SR604/604E and TX-SR8460 Only Table of Contents Front & Rear Panels Front PanelFront & Rear Panels Display XM antenna on North American models Rear PanelDigital Optical in 1, 2, 3 and OUT Hdmi in 1, 2, and OUTZone 2 Line OUT Installing the Batteries Remote ControllerAiming the Remote Controller Using the Remote Controller Remote ControllerRECEIVER/TAPE Mode Buttons used when the Tape input is selected Remote Mode buttonsButtons used when the Tuner input is selected Zone 2 buttonDVD Mode DISC/ALBUM +/- button CD/MD/CDR/HDD ModeTo select the input source, press Arrow / and Enter buttonsAbout Home Theater Enjoying Home TheaterOptical Digital Jacks Connecting the AV ReceiverAbout AV Connections AV Connection Color CodingConnecting the AV Receiver Connecting Your SpeakersRead the following before connecting your speakers Speaker Connection PrecautionsConnecting the Speaker Cables Strip about 5/8 15 mmConnecting the AM Loop Antenna Connecting AntennaConnecting the Indoor FM Antenna Attach the FM antenna, as shown North American modelsConnecting an Outdoor AM Antenna Connecting an Outdoor FM AntennaUsing a TV/FM Antenna Splitter Video Connection Formats Connecting Both Audio & VideoWhich Connections Should I Use? Audio Connection FormatsAudio Connection Connecting Your TV or ProjectorVideo Connection HintConnecting a DVD Player Hooking Up the Multichannel DVD Input DVD playerConnecting a VCR or DVD Recorder for Playback DVD recorderConnecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Camcorder, Games Console, or Other Device Supported Audio Formats Connecting Components with HdmiAbout Hdmi About Copyright ProtectionMaking Hdmi Connections Video Signal Flow ChartAudio Signal Flow Chart TX-SR604/604E, TX-SR8460Connecting a CD Player or Turntable CD Player or Turntable MM with Built-in Phono Preamp StepAudio output jacks and video output jack to the AV Connecting a HDD-compatible ComponentConnect your HDD-compatible component’s analog Receiver’s Video 3 in L/R jacks and Video 3 JacksConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Auto Power On/Standby Connecting Onkyo ComponentsConnecting the Power Cord of Another Component Remote ControlTurning On the AV Receiver Connecting the Power CordDo the automatic speaker setup-this is essential Turning On and StandbyAutomatic Speaker Setup Audyssey2EQ First Time SetupMeasurement Points Connect the setup microphone to the Setup MIC jack First Time SetupPress Enter Following screen appears When the calculations are comDisconnect the speaker setup Plete, the following screenReviewing the Results Error MessagesSpeaker Detect Errors Ambient noise is too highUsing a Powered Subwoofer Changing the Speaker Settings ManuallyPress the Return button to return to the previous menu Submenus About the Onscreen Setup MenusMain menu Digital Input Hdmi Video Setup Video InputSetup menu closes Component Video SetupMain menu appears onscreen Changing the Input Display Minimum Speaker Impedance not North American modelsHardware Setup menu appears TV Format Setup Not North American modelsAM Frequency Step Setup on some models You must specify the TV system used in your areaStart playback on the source component Basic OperationsSelecting the Input Source Video OUT, Hdmi OUT or Monitor OUTBasic Operations Using the Multichannel DVD InputAdjusting the Bass & Treble Displaying Source InformationUsing Headphones Using the Sleep TimerSetting the Display Brightness Muting the AV ReceiverListening to the Radio Using the TunerTuning into Radio Stations Listening to the RadioDeleting Presets Presetting AM/FM Stations XM ChannelsSelecting Presets Listening to the RadioWhat is RDS? Using RDS European models onlyRDS Program Types PTY Listening to Traffic News TP Displaying Radio Text RTFinding Stations by Type PTY Important XM Radio Information Connecting the XM Passport SystemListening to XM Satellite Radio North American models only About XM RadioSigning Up for XM Satellite Radio Setting the Satellite Radio ModeSelecting XM Satellite Radio There are three ways to select XM radio channels Channel Search mode select any channelSelecting XM Radio Channels Receiver button flashesDisplaying XM Radio Information Positioning the XM Passport System TER signal strength bar is asXM Radio Messages Long as possibleSelecting Listening Modes Using the Listening ModesSelecting with the Remote Controller Selecting on the AV ReceiverUsing the Listening Modes DVDAbout the Listening Modes Use this mode with any stereo movie e.g., TV, DVD, VHS Onkyo Original DSP ModesAV Recording RecordingRecording Separate AV Sources Adjusting Individual Speaker Levels Using the CinemaFILTERUsing the Late Night Function Dolby Digital only Advanced OperationsSpeaker Setup Advanced SetupSpeaker Config menu appears Low-Pass Filter for the LFE Channel Advanced SetupDouble Bass Speaker Distance menu appears Speaker DistanceTance, and then press Enter Buttons to select 2. Speaker DisTest tone from each speaker Repeat until the volumeSpeaker Level Calibration Is the sameEqualizer Settings menu appears Equalizer SettingSettings, and then press Buttons to select 4. EqualizerWhen you’ve finished, press Multichannel DVD Input SettingsAudio Adjust Functions SW Input SensitivityNeo6 Music Mode Setting Input Channel SettingsPL IIx Music Mode Settings Dolby Digital EX Input Signal SettingUse the Input Selector but Tons on the remote controller toAssigning Listening Modes to Input Sources Select the input source that youUse the Up and Down Buttons to select a. IntelliVolume IntelliVolumeVolume Setup/OSD Setup Lowed by the Setup button. The main menu appears onscreenChanging the AV Receiver’s ID Hdmi Audio OutPress and hold the AV receiver’s Digi Lock SetupDigital Input Signal Formats TAL Input button for about 3 secondsPress the Receiver and the Cine Changing the Remote Controller’s IDCorrecting Sound and Picture Sync Fltr at the same timeUsing Only Speakers in Zone Connecting ZoneUsing a Receiver/Integrated Amp in Zone ZoneSetting the Powered Zone Buttons to select Powered ZoneControlling Zone 2 with the Remote Controller Using ZoneControlling Zone 2 from the AV receiver Using a Multiroom Kit with Zone Using the Remote Control in ZoneAdjusting the Volume for Zone Using a Multiroom Kit with a CabinetEntering Remote Control Codes Controlling Other ComponentsResetting the Remote Controller Remote Control Codes for Onkyo Components Connected viaResetting Remote Mode Buttons Controlling Other ComponentsTV VOL CH +Video Section SpecificationsAmplifier Section Tuner SectionTroubleshooting Troubleshooting Onscreen menus don’t appear Remote controller doesn’t workThere’s no picture from a source connected to an Hdmi Immediate display does not appearThere’s no sound Sound changes when I connect my head- phonesSpeaker volume cannot be set as required Speaker distance cannot be set as requiredMemo Onkyo Europe Electronics GmbH Onkyo Europe UK Office