Onkyo TX-SR502E Connecting Onkyo Components, Connecting the Power Cords of Other Components

TX-SR502_En.book Page 30 Tuesday, February 17, 2004 12:14 PM

Connecting the TX-SR502/TX-SR502E—Continued

Connecting Onkyo Components

To use , you must make an analog audio connection (RCA) between the TX-SR502/ TX-SR502E and the other component, even if they are connected digitally.

With (Remote Interactive) you can control your

-compatible Onkyo CD player, DVD player, and so on with the TX-SR502/TX-SR502E’s remote controller,

and use the following special functions:

Auto Power On/Standby

When you start playback on a component connected via

, if the TX-SR502/TX-SR502E is in Standby, it will turn on and select that component as the input source automatically. Similarly, when the TX-SR502/ TX-SR502E is set to Standby, all components connected

via also enter Standby. This function will not work if the component’s power cord is connected to the TX-SR502/TX-SR502E’s AC OUTLET.

Direct Change

When playback is started on a component connected via

, the TX-SR502/TX-SR502E automatically selects that component as the input source. If your DVD player is connected to the TX-SR502/TX-SR502E’s multichan- nel input, you must press the [MULTI CH] button to enjoy all channels (see page 34). This is because the

Direct Change function only selects the FRONT DVD IN sockets.

Remote Control

You can use the TX-SR502/TX-SR502E’s remote con-

troller to control other -compatible Onkyo compo- nents.

IN

				L
COMPONENT VIDEO		ANTENNA	FM	R
VIDEO 1 /2/3IN DVD IN	OUT	AM	75
		Y

P CD

REMOTE		P	VIDEO 2	VIDEO 1		DVD	MONITOR
CONTROL	DIGITAL IN		IN	OUT	IN	IN	OUT
			CONTROL
			REMOTE
	OPTICAL	COAXIAL					VIDEO

3	2		1
								S VIDEO	FRONT
	IN	OUT	IN	IN	IN	OUT	IN	FRONT SURR CENTER	L
	L			L				L
SUBWOOFER
PRE OUT

R		R	R
	TAPE	VIDEO 2		SUB	R
CD			VIDEO 1	WOOFER
			DVD

DVD

e.g., CD player

R L

ANALOG

AUDIO OUT

e.g., DVD player

R L

ANALOG

AUDIO OUT

Notes:

•Push plugs in all the way to make good connections.

•Use only cables for connections. cables are supplied with Onkyo players (DVD, CD, etc.).

•Some components have two sockets, you can con- nect either one to the TX-SR502/TX-SR502E. The

other is for connecting additional -compatible components.

30

•Connect the TX-SR502/TX-SR502E’s socket to only Onkyo components. Connecting to other manu- facturer’s components may cause them to malfunc- tion.

•Some components may not support all functions. Refer to the manuals supplied with your components.

Connecting the Power Cords of Other Components

The TX-SR502/TX-SR502E has AC outlet on its rear panel for connecting the power cord of another AV com- ponent. The other component’s power switch can be left in the ON position so that it turns on or off when the TX-SR502/TX-SR502E is set to On or Standby.

Class 2 Wiring

				AC OUTLET
FRONT	FRONT	SURROUND	CENTER	AC 120V 60 Hz
SPEAKERS B	SPEAKERS A	SPEAKERS	SPEAKER	SWITCHED
L	L	L		120W 1 A MAX.
R	R	R
			SURROUND BACK
			SPEAKER

AV RECEIVER

MODEL NO. TX-SR502

AC OUTLET	AC OUTLET
SWITCHED	AC 120V 60 Hz
100W MAX.	SWITCHED
	120W 1 A MAX.

European and some	American model
Asian models

Caution:

•Make sure that the capacity of the component that you connect to the AC OUTLET does not exceed the stated capacity (e.g., 100 W).

Note:

•Onkyo components with sockets should be con- nected to regular wall outlets.

•The connector type and capacity will depend on the country in which you purchased the TX-SR502/ TX-SR502E.

Connecting the Power Cord

Notes:

•Before connecting the power cord, connect all of your speakers and AV components.

•Turning on the TX-SR502/TX-SR502E may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the TX-SR502/TX-SR502E into a different branch circuit.