Onkyo TX-SR502E Specifications, Amplifier Section, General, Video Section, Tuner Section

Specifications

Amplifier Section

Power output:	75 W (8 Ω, 20 Hz–20 kHz, FTC)
All channels:	105 W (6 Ω, 1 kHz, DIN)
	130 W (6 Ω, 1 kHz, EIAJ)
Dynamic power:	2 x 180 W (3 Ω, front)
	2 x 150 W (4 Ω, front)
	2 x 95 W (8 Ω, front)
THD (total harmonic
distortion):	0.08% (rated power)
Damping factor:	60 (front, 1 kHz, 8Ω)
Input sensitivity and	200 mV/47 k Ω (LINE)
impedance:
Output level and	200 mV/470 Ω (REC OUT)
impedance:
Frequency response:	10 Hz–100 kHz/+1 dB, –3 dB (Direct
	mode)
Tone control:	±12 dB, 50 Hz (BASS)
	±12 dB, 20,000 Hz (TREBLE)
S/N ratio (Direct mode): 100 dB (CD, IHF-A)
Speaker impedance:	6 Ω~

General

Power supply:	American model: AC 120 V, 60 Hz
	Worldwide model: AC 220–230 V and
	120 V switchable 50/60 Hz
	Other models: AC 230–240 V, 50 Hz
	AC 220–230 V, 50 Hz
Power consumption:	American model: 4.6 A
	Other models: 370 W
Standby power
consumption:	2.5 W
Dimensions
(W x H x D):	17-1/8" x 5-7/8" x 14-13/16"
	(435 x 150 x 376 mm)
Weight:	American, European and Australian
	models: 22.5 lbs. (10.2 kg)
	Asian model: 24.3 lbs. (11.0 kg)

■Video Inputs

Component video inputs:2		(DVD, Video 1/2/3)
S-Video inputs:	4	(DVD, Video 1–3)
Video inputs:	4	(DVD, Video 1–3)

Video Section

Input sensitivity, output

level and impedance: 1.0 Vp-p/75 Ω (component and S-Video Y)

0.7Vp-p/75 Ω (component PB/CB, PR/CR)

0.28Vp-p/75 Ω (S-Video C)

1.0Vp-p/75 Ω (composite)

Component video

frequency response: 5 Hz–50 MHz

Tuner Section

■FM

Tuning frequency range: 87.5–108.0 MHz

Usable sensitivity:	FM STEREO 17.2 dBf, 2.0 µV (75 Ω
	IHF)
	FM MONO 11.2 dBf, 1.0 µV (75 Ω IHF)
S/N ratio:	FM STEREO 70 dB (IHF-A)
	FM MONO 76 dB (IHF-A)
THD:	FM STEREO 0.3% (1 kHz)
	FM MONO 0.2% (1 kHz)
FM stereo separation:	45 dB at 1 kHz

■AM

Tuning frequency range: 530–1700 kHz (American model)

	522–1611 kHz (Other models)
Usable sensitivity:	30 µV
S/N ratio:	40 dB
THD:	0.7%

■Video Outputs

Component video
outputs:	1	(Component Video Out)
S-Video outputs:	2	(Video 1 Out, Monitor Out)
Video outputs:	2	(Video 1 Out, Monitor Out)

■Audio Inputs

Digital inputs:	4	(Optical 1–3, Coaxial)
Analog inputs:	6	(CD, Tape, DVD, Video 1–3)
Multichannel analog
inputs:	5.1 ch (Front L/R, Center, Surround L/R,
		Subwoofer)

■Audio Outputs

Analog outputs:	2 (Tape Out, Video 1 Out)
Subwoofer pre out:	1
Speaker outputs:	6+2
Phones:	1

Specifications and features are subject to change without notice.

•The AV Receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely even that this should happen, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again. That should fix it.

•To reset the AV Receiver to its factory defaults, turn it on and, while holding down the [VIDEO 1] button, press the [STANDBY/ON] button. “Clear” will appear on the display and the AV Receiver will enter Standby mode.

59