Multifunctional Settings (continued)
OPTION Menu
With the OPTION menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.
MENU
MAIN | VOLUME | 16 |
SPEAKER | TURN ON | |
IR REMOTE |
| |
INPUT | IR REMOTE ID | ALL |
AUTO | LAMP TIME | 1234 h |
SCREEN | FILTER TIME | 4321 h |
OPTION | SERVICE |
|
NETWORK | PIN LOCK | TURN ON |
: SELECT |
|
|
Item |
|
| Description |
|
| ||
|
|
|
|
|
| ||
VOLUME | Adjust the volume using the / | buttons. : |
|
| |||
High Low |
|
|
|
|
| ||
|
|
|
|
|
| ||
|
|
|
|
| |||
| Select the TURN ON or the TURN OFF using the / buttons. : |
|
| ||||
SPEAKER | TURN ON TURN OFF |
|
|
|
|
| |
| When the TURN ON is selected, the |
|
| ||||
|
|
|
|
|
| ||
| Select a remote sensor using the | / button (1), then switch it |
|
| |||
|
| OPTION |
| ||||
| using the ENTER button (2). : |
|
| IR REMOTE |
| ||
|
|
| 1:FRONT |
| |||
IR REMOTE | (1) 1:FRONT 2:TOP 3:REAR (2) (Off) (On) |
|
| ||||
| 2:TOP |
| |||||
|
|
|
|
|
| ||
| memo A sensor cannot be turned off when the other two are off. |
| 3:REAR |
| |||
|
| ENT |
| ||||
| Always at least one sensor is on. |
|
|
|
| ||
|
|
|
|
|
|
| |
| Select a number as an ID number for remote control using the / | buttons. : | |||||
| ALL 1 2 3 |
|
|
|
|
| |
| The projector is controlled by the remote control whose ID CHANGE switch is | ||||||
IR REMOTE ID | set into the position of the same number as this number. When the ALL is | ||||||
| selected, the projector is controlled by a remote control irrespective of the | ||||||
| position of the ID CHANGE switch. |
|
| ||||
| memo Please refer to the section “Using The Remote ID Feature”. |
|
| ||||
|
|
|
| ||||
| Pressing the RESET button for about 3 seconds displays the LAMP TIME menu. | ||||||
| Select the RESET using | button to reset the timer. : |
|
| |||
| RESET CANCEL |
|
|
|
|
| |
LAMP TIME | Selecting the RESET resets the count of the lamp timer to 0. |
|
| ||||
memo Perform this function only when you have replaced the lamp. The lamp | |||||||
| |||||||
| timer counts the used time of the current lamp, to display the messages about | ||||||
| the lamp. Incorrect performing causes incorrect operation of the messages. | ||||||
| memo About replacing the lamp, please refer to the section” Lamp”. |
|
| ||||
|
|
|
| ||||
| Pressing the RESET button for about 3 seconds displays the FILTER TIME | ||||||
| menu. |
|
|
|
|
| |
| Select the RESET using | button to reset the timer. : |
|
| |||
| RESET CANCEL |
|
|
|
|
| |
FILTER TIME | Selecting the RESET resets the count of the lamp timer to 0. |
|
| ||||
memo Perform this function only when you have cleaned or replaced the air | |||||||
| |||||||
| filter. The filter timer counts the used time of the air filter after cleaning or | ||||||
| replacement, to display the messages about the air filter. Incorrect performing | ||||||
| causes incorrect operation of the messages. |
|
| ||||
| memo About caring for the air filter, please refer to the section “Air Filter”. | ||||||
|
|
|
|
|
| ||
|
|
| (This table is continued to the following page.) |
© 3M 2004 3M™ Multimedia Projector X70/X80 | 33 |