Interlink electronic X70/X80 manual Lamp

Page 37

Lamp

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash. Dispose of in accord with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in USA)

For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

If the lamp should break (it will make a loud bang when it does), ventilate

Disconnect the the room well, and make sure not to breathe the gas that comes out of plug from the the projector vents, or get it in your eyes or mouth.

power outlet

Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

Do not open the lamp door while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the door is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

Use only the lamp of the specified type 78-6969-9718-4 for X70 / 78- 6969-9719-2 for X80.

If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

If the indicators or a message prompts you to replace the lamp (see the section “Related Messages” and “Regarding the indicator Lamps”), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

© 3M 2004 3M™ Multimedia Projector X70/X80

37

 

Image 37
Contents X70/X80 Preparation Projector FeaturesContents Page Page Arrangement Setting UpPage Connecting Your Devices Page If using a component signal If using a s-video signalIf using a Scart RGB input VCR/DVD Player ProjectorPage About The Laser Pointer Remote ControlPutting Batteries Page + + + Using The Mouse/Keyboard Control FunctionPage Operating Selecting An Input SignalAt a M1-D signal Using The Automatic Adjustment FeatureAt a RGB signal not M1-D At a video signal At a RGB signalCorrecting The Keystone Distortion Adjusting The Picture PositionMuting The Sound Adjusting The VolumeTemporarily Blanking The Screen Freezing The Screen Using The Magnify FeatureSelecting An Audio Input Displaying The Child WindowUsing The Menu Functions Multifunctional SettingsMain Menu PICTURE-1 Menu MY Memory PICTURE-1 MenuPICTURE-2 Menu PhasePosition SizeVideo NR Input MenuInput Menu Power OFF AdjustPower on Auto MenuSearch Auto MenuMenu Position Screen MenuScreen Menu How to register your picture as the MyScreenOption Menu Option Menu Network Menu SetupDhcp Ex. Case of IP Address = Network Setting UpLamp Replacing The Lamp Case of replacement by yourselfCaring For The Air Filter Air FilterOther Care Caring For The Cabinet And Remote ControlCaring For The Inside Of The Projector Caring For The LensRelated Messages TroubleshootingRelated Messages Regarding The Indicator Lamps Regarding The Indicator Lamps Not been properly fixed Phenomena That May Easily Be Mistaken For Machine DefectsSound is muted Phenomena That May Easily Be Mistaken For Machine DefectsSpecification SpecificationsAccessories Part Number AccessoriesHow to Order Not Included with Basic Packet Part NumberIntended Use