Meridian Audio FDP-DILA3 warranty Basic Operations, Basic Operation Procedures, Power On

Page 24

Light on

Basic Operations

If projector set up is not yet complete, please read ‘Adjustments and Settings Using Menus’ on page 31 and perform the necessary settings.

STAND BY

LAMP TEMP OPERATE

PC

VIDEO

1-2

2

V-KEYSTONE H-KEYSTONE

VOL.

MENUEXIT

Basic Operation Procedures

Once the basic settings are done, follow the procedures below:

1. Power On

1 The STAND BY indicator lights up when the power cord is connected.

STAND BY

LAMP TEMP OPERATE

Projector: Indicator part

2Press the OPERATE button on the projector (or the OPER- ATE button on the remote control unit) for one second or more.

The OPERATE indicator lights up and the projected screen ap- pears slowly.

ENTER

1-2

OPERATE

	OPERATE
Projector:	Remote control
Control panel	unit

Light on

STAND BY

LAMP TEMP OPERATE

Projector : Indicator

PC	VIDEO		OPERATE	2
PC	VIDEO			2
		W
V-KEYSTONE H-KEYSTONE		SCREEN	DIGITAL
V-KEYSTONE H-KEYSTONE		SCREEN	ZOOM
			ZOOM
		S
			FREEZE
VOLUME	FOCUS	QUICK ALIGN.
MENU			EXIT
	ENTER
PRESET			HIDE

Note

•Messages are displayed in the language set by the user in the “Language” menu. The pre- set language upon purchase is “English”. The user can choose from 8 national languages.

However, the input mode (PC 1, PC 2, PC 3, Y/C, VIDEO) and button indications (FREEZE, D.ZOOM, EXIT) are only displayed in English irrespective of the display language setting.

Notes

•Upon projection, the image may flicker for a few seconds, but this is not a malfunction.

•When the lamp is turned on, it will slowly become brighter. It will take more than a minute for the brightness to stabilize.

2.Selecting the image to be projected

When you select an image device to be connected to the VIDEO IN (VIDEO or Y/C) terminal: press VIDEO.

	VIDEO
VIDEO
Projector:	Remote Control
Control panel	Unit

Each time you press either button, the selected input changes as follows.

VIDEO : Image from the input VIDEO ter- minal on the right hand side of pro- jector will be projected.

Y/C : Image from the input Y/C terminal on the right hand side of the pro- jector will be projected.

24

Image 24

Contents Model No. FDP-DILA3 Serial NoAbout the installation place FCC Information U.S.A. onlyMachine Noise INFORMATIONGermany only About burning-in of the D-ILA deviceSafety Precaution Do not allow any unqualified person to install the unitWire which is coloured green-and-yellow must be con How To Replace The FuseBrown Live Do not cut off the main plug from this equipmentUsing the screen mode switch function Viewing conditionsCare Pecifications Dimensions Pin arrangement Aution Acces s ories Ontrols and F eaturesMenu C onfiguration Eplacing the L ampControls and Features Front Side/Top Surface/Left SideConnector Panel Controls and FeaturesIndicator Display on the Control Panel Control Panel on the ProjectorStand by light on Operate light on Stand by blinking Alternately*2Stand by Indicator Operate IndicatorVolume ª / · buttons Temp IndicatorRemote Control Unit Remote Control’s signal transmitterRemote Control’s signal transmitter Operate button Volume ª / · buttonScreen button Digital Zoom ª / · buttonsLoading Batteries into the Remote Control Precautions for using batteriesOpen the back cover Load the batteriesInstalling the Projector Precautions for InstallationInstalling the Projector against the Screen Installing the ProjectorPrecaution for ceiling-mount Mounting the ProjectorScreen installation Projection Distance and Screen SizeEffective Range and Distance of the Remote Control Unit Using as a wireless remote control unit Using as a wired Remote Control When the remote control unit fails to work properlyConnecting to Various Devices Signals that can be input into the projector Video signals Computer signalsConnecting to Various Devices Allowable input signalsSignal HorPixels Ver Lines KHzOnnecting to Various Devices Connecting to Computers Control from external device Connection for controlling more than one projectorConnecting the Power Cord supplied Power cord suppliedBasic Operation Procedures Power OnBasic Operations Selecting the image to be projected Display using the direct buttons Adjusting the Focus RingFocus Remove top cover to accessBasic Operations Power Off Adjusting the Sound Volume Digital zoom Display Frequently used Convenient FunctionsEnlarging the Image Turning Off Image and Sound Displaying a Still PicturePress the Hide button once Press the Freeze buttonPress V-KEYSTONE / to adjust in the vertical direction Press H-KEYSTONE / to adjust in the horizontal directionRemoving the Trapezoidal Distortion of the Image Vert. Keystone DisplayUsing the Quick Alignment function Selecting the Screen Size Screen size display Press the Quick Align Quick Alignment buttonAdjustments and Settings Using Menus Menu StructureMenus of the projector have the following structure Main menu SubmenuCapture menu Capture start Adjustments and Settings Using Menus SubmenuMenu Operation Buttons Procedure for Menu Operation Menu Configuration Set up menuImage adj. menu Color temp. menuLogo menu Position menuDecoder menu Capture menuCapture start Options menu qColor profile menu Language menuWhen no image signal is inputted Information menuEditing and Projecting Logo Project the images to be included in your logoSelect Logo with the Cursor buttons / Press the Enter or the right Cursor button Editing and projecting logo Set the menu position as requiredSelect Vert. move with the Cursor buttons / Select Horiz. size with the Cursor buttons / Procedure for lamp replacement About lamp replacementReplacing the Lamp Light source lamp and its lamp timeReplacing the Lamp Remove the lamp unitInsert the new lamp unit fully Close the handle, and tighten the screwResetting the lamp time Cleaning and Replacing the Filter Pull out the power cord from the wall outletClean the filter Reinstalling the filterTroubleshooting Symptom Probable cause Corrective actionTroubleshooting FuzzyWhat to do when these messages are displayed Message Cause ContentsWhat to do when these messages are displayed About warning indicators Please follow the procedures below Action to be taken upon warning indications Cooling fan has stopped. Fan lockedSpecifications Specifications Specifications Pin arrangement Y/C terminal RS-232C IN/OUT terminal PC 1 terminalCommunication Specifications Command Format RS-232C external control HeaderExternal control command table Operation mode parameters Character Hex MeaningOperation mode Only Asking command is possible FunctionFaroudja Warranty Statement FDP-DILA3 Theater Optimized Package