Meridian Audio FDP-DILA3 warranty Troubleshooting, Fuzzy

Page 47

Troubleshooting

Symptom

Probable cause

Corrective action

Page

 

 

 

 

Video image is

Is focus adjusted correctly?

Adjust focus with the focus ring of the lens.

25

fuzzy.

 

 

 

Is the projector placed too near or too far from

Set the projector at the correct distance.

16

 

 

the screen?

 

 

 

 

 

 

 

Are “Tracking” and “Phase” adjusted correctly?

Adjust “Tracking” and “Phase” on the menu.

36

 

 

 

 

Video image is ab-

Is “Brightness” adjusted correctly?

Adjust “Brightness” on the menu.

36

normally dark or

 

 

 

bright.

 

 

 

 

 

 

 

Color is poor or un-

Is picture quality (color, density, etc.) adjusted

Adjust picture quality on the menu.

36

stable.

correctly?

 

 

 

 

 

 

 

Is the correct “Decoder” selected?

Set the “Decoder” to “AUTO” or the correct

37

 

 

dedicated decoder.

 

 

 

If the problem is not rectified after setting to

 

 

 

“AUTO”, set to forced dedicated mode.

 

 

 

 

 

 

Are signals (scanning frequency, etc.) from the

Check if the signal is appropriate (scanning fre-

18, 19

 

connected device appropriate?

quency, etc.), and input the appropriate signal.

 

 

 

 

 

 

Is the PC2 input terminal being used?

When the PC2 input terminal is being used,

38

 

 

“PC 2(BNC)” must be selected from the

 

 

 

“Options” menu. Set it correctly according to

 

 

 

the input signal.

 

 

 

 

 

The upper part of

While computer signals are input, are sync sig-

Input separate sync signals for vertical sync

18, 19

the video image

nals for composite sync (Cs) or G on sync be-

(V) and horizontal sync (H) signals.

 

bows or distorts.

ing inputted?

 

 

 

 

 

 

 

Are signals with much jitter or skew distortion

Input signals with little jitter or skew distortion.

—————

 

being input from a video deck?

Use a TBC or a device with a built-in TBC.

 

 

 

 

 

Remote control unit

Are batteries installed correctly?

Match the polarities of batteries correctly, as

13

does not work.

 

shown on the battery cartridge.

 

 

 

 

 

 

Are batteries exhausted?

Replace with new batteries.

13

 

 

 

 

 

Is there an obstructive object between the re-

Remove any shielding objects.

17

 

mote control unit and the remote sensor?

 

 

 

 

 

 

 

Is the remote control held too far from the sen-

Use the remote control unit at a nearer point.

17

 

sor?

 

 

 

 

 

 

This projector uses a micro computer. External noise may cause it to malfunction. If this happens, unplug from the main power outlet and then plug on again. (page 24, 26)

47

Image 47
Contents Serial No Model No. FDP-DILA3About burning-in of the D-ILA device About the installation placeFCC Information U.S.A. only Machine Noise INFORMATIONGermany onlyDo not allow any unqualified person to install the unit Safety PrecautionDo not cut off the main plug from this equipment Wire which is coloured green-and-yellow must be conHow To Replace The Fuse Brown LiveCare Using the screen mode switch functionViewing conditions Eplacing the L amp Pecifications Dimensions Pin arrangementAution Acces s ories Ontrols and F eatures Menu C onfigurationFront Side/Top Surface/Left Side Controls and FeaturesControls and Features Connector PanelAlternately*2 Indicator Display on the Control PanelControl Panel on the Projector Stand by light on Operate light on Stand by blinkingTemp Indicator Stand by IndicatorOperate Indicator Volume ª / · buttonsRemote Control’s signal transmitter Remote Control UnitDigital Zoom ª / · buttons Remote Control’s signal transmitter Operate buttonVolume ª / · button Screen buttonLoad the batteries Loading Batteries into the Remote ControlPrecautions for using batteries Open the back coverPrecautions for Installation Installing the ProjectorMounting the Projector Installing the Projector against the ScreenInstalling the Projector Precaution for ceiling-mountProjection Distance and Screen Size Screen installationWhen the remote control unit fails to work properly Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit  Using as a wired Remote Control Computer signals Connecting to Various DevicesSignals that can be input into the projector  Video signalsHorPixels Ver Lines KHz Connecting to Various Devices Allowable input signals SignalOnnecting to Various Devices  Connecting to Computers Connection for controlling more than one projector  Control from external devicePower cord supplied Connecting the Power Cord suppliedSelecting the image to be projected Basic Operation ProceduresPower On Basic OperationsBasic Operations  Display using the direct buttonsAdjusting the Focus RingFocus Remove top cover to access Adjusting the Sound Volume Power OffEnlarging the Image  Digital zoom DisplayFrequently used Convenient Functions Press the Freeze button Turning Off Image and SoundDisplaying a Still Picture Press the Hide button once Vert. Keystone Display Press V-KEYSTONE / to adjust in the vertical directionPress H-KEYSTONE / to adjust in the horizontal direction Removing the Trapezoidal Distortion of the ImagePress the Quick Align Quick Alignment button Using the Quick Alignment functionSelecting the Screen Size  Screen size displayMenus of the projector have the following structure Adjustments and Settings Using MenusMenu Structure Capture menu Capture start Main menuSubmenu Submenu Adjustments and Settings Using MenusMenu Operation Buttons Procedure for Menu Operation Color temp. menu Menu ConfigurationSet up menu Image adj. menuCapture menu Logo menuPosition menu Decoder menuLanguage menu Capture startOptions menu q Color profile menuInformation menu When no image signal is inputtedPress the Enter or the right Cursor button  Editing and Projecting LogoProject the images to be included in your logo Select Logo with the Cursor buttons  / Select Horiz. size with the Cursor buttons  /  Editing and projecting logoSet the menu position as required Select Vert. move with the Cursor buttons  / Light source lamp and its lamp time Procedure for lamp replacementAbout lamp replacement Replacing the LampClose the handle, and tighten the screw Replacing the LampRemove the lamp unit Insert the new lamp unit fullyResetting the lamp time Reinstalling the filter Cleaning and Replacing the FilterPull out the power cord from the wall outlet Clean the filterSymptom Probable cause Corrective action TroubleshootingFuzzy TroubleshootingMessage Cause Contents What to do when these messages are displayedWhat to do when these messages are displayed Cooling fan has stopped. Fan locked  About warning indicatorsPlease follow the procedures below  Action to be taken upon warning indicationsSpecifications Specifications  PC 1 terminal SpecificationsPin arrangement  Y/C terminal  RS-232C IN/OUT terminalHeader Communication SpecificationsCommand Format  RS-232C external controlFunction External control command tableOperation mode parameters Character Hex Meaning Operation mode Only Asking command is possibleFaroudja Warranty Statement FDP-DILA3 Theater Optimized Package