Meridian Audio FDP-DILA3 warranty Power Off, Adjusting the Sound Volume

Page 26

Basic Operations

5. Adjusting the Sound Volume

To increase the volume: press VOLUME ª (0 50)

 

 To lower the volume : press VOLUME · (50 0)

VOL.

VOLUME

STAND BY

LAMP TEMP OPERATE

PCVIDEO

V-KEYSTONE H-KEYSTONE

VOL.

MENUEXIT

ENTER

OPERATE

5

Projector:

Remote Control

Control panel

Unit

Audio-Vol

12

Screen display

When “Menu display” (page 38) is set to “15sec”, after pressing the VOLUME button, the sound vol- ume display will appear on the screen for about 15 seconds. (Press EXIT button to immediately remove the Audio-vol display.)

Audio-Vol

OPERATE

PC VIDEO

W

V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM

 

S

 

FREEZE

VOLUME FOCUS

QUICK ALIGN.

MENU

EXIT

ENTER

 

OPERATE

5

Note

When the sound volume is displayed on the screen, pressing the PRESET button will reset the set value to “0”.

Power Off

1. Press the OPERATE button on the projector (or the OP- ERATE button on the remote control unit ) for 1 second or more.

The OPERATE indicator will disappear, the STAND BY indicator starts to blink , and the projector goes into the cool-down mode.

The STAND BY indicator will continue blinking for approximately 90 seconds as the temperature of the light source lamp cools (Cool Down Mode)

PRESET

HIDE

OPERATE

 

OPERATE

Projector:

Remote Control

Control Panel

Unit

Turn off Turn on

STAND BY

LAMP TEMP OPERATE

Projector: Indicator part

Note

The OPERATE button will not work for approximately 1 minute from when the light-source lamp is turned on. Please use the button after approximately 1 minute.

Caution

Please do not pull out the plug from the power source when the STAND BY indicator is blinking. It will shorten the life of the lamp and cause malfunction.

26

Image 26
Contents Model No. FDP-DILA3 Serial NoMachine Noise INFORMATIONGermany only About the installation placeFCC Information U.S.A. only About burning-in of the D-ILA deviceSafety Precaution Do not allow any unqualified person to install the unitBrown Live Wire which is coloured green-and-yellow must be conHow To Replace The Fuse Do not cut off the main plug from this equipmentCare Using the screen mode switch functionViewing conditions Menu C onfiguration Pecifications Dimensions Pin arrangementAution Acces s ories Ontrols and F eatures Eplacing the L ampControls and Features Front Side/Top Surface/Left SideConnector Panel Controls and FeaturesStand by light on Operate light on Stand by blinking Indicator Display on the Control PanelControl Panel on the Projector Alternately*2Volume ª / · buttons Stand by IndicatorOperate Indicator Temp IndicatorRemote Control Unit Remote Control’s signal transmitterScreen button Remote Control’s signal transmitter Operate buttonVolume ª / · button Digital Zoom ª / · buttonsOpen the back cover Loading Batteries into the Remote ControlPrecautions for using batteries Load the batteriesInstalling the Projector Precautions for InstallationPrecaution for ceiling-mount Installing the Projector against the ScreenInstalling the Projector Mounting the ProjectorScreen installation Projection Distance and Screen Size Using as a wired Remote Control Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit When the remote control unit fails to work properly Video signals Connecting to Various DevicesSignals that can be input into the projector  Computer signalsSignal Connecting to Various Devices Allowable input signals HorPixels Ver Lines KHzOnnecting to Various Devices  Connecting to Computers  Control from external device Connection for controlling more than one projectorConnecting the Power Cord supplied Power cord suppliedBasic Operations Basic Operation ProceduresPower On Selecting the image to be projectedBasic Operations  Display using the direct buttonsAdjusting the Focus RingFocus Remove top cover to access Power Off Adjusting the Sound VolumeEnlarging the Image  Digital zoom DisplayFrequently used Convenient Functions Press the Hide button once Turning Off Image and SoundDisplaying a Still Picture Press the Freeze buttonRemoving the Trapezoidal Distortion of the Image Press V-KEYSTONE / to adjust in the vertical directionPress H-KEYSTONE / to adjust in the horizontal direction  Vert. Keystone Display Screen size display Using the Quick Alignment functionSelecting the Screen Size Press the Quick Align Quick Alignment buttonMenus of the projector have the following structure Adjustments and Settings Using MenusMenu Structure Capture menu Capture start Main menuSubmenu Adjustments and Settings Using Menus SubmenuMenu Operation Buttons Procedure for Menu Operation Image adj. menu Menu ConfigurationSet up menu Color temp. menuDecoder menu Logo menuPosition menu Capture menuColor profile menu Capture startOptions menu q Language menuWhen no image signal is inputted Information menuSelect Logo with the Cursor buttons  /  Editing and Projecting LogoProject the images to be included in your logo Press the Enter or the right Cursor button Select Vert. move with the Cursor buttons  /  Editing and projecting logoSet the menu position as required Select Horiz. size with the Cursor buttons  / Replacing the Lamp Procedure for lamp replacementAbout lamp replacement Light source lamp and its lamp timeInsert the new lamp unit fully Replacing the LampRemove the lamp unit Close the handle, and tighten the screwResetting the lamp time Clean the filter Cleaning and Replacing the FilterPull out the power cord from the wall outlet Reinstalling the filterTroubleshooting Symptom Probable cause Corrective actionTroubleshooting FuzzyWhat to do when these messages are displayed Message Cause ContentsWhat to do when these messages are displayed  Action to be taken upon warning indications  About warning indicatorsPlease follow the procedures below Cooling fan has stopped. Fan lockedSpecifications Specifications  Y/C terminal  RS-232C IN/OUT terminal SpecificationsPin arrangement  PC 1 terminal RS-232C external control Communication SpecificationsCommand Format HeaderOperation mode Only Asking command is possible External control command tableOperation mode parameters Character Hex Meaning FunctionFaroudja Warranty Statement FDP-DILA3 Theater Optimized Package