Meridian Audio FDP-DILA3 Replacing the Lamp, Remove the lamp unit, Insert the new lamp unit fully

Page 43

Replacing the Lamp

3. Remove the lamp unit.

Lamp unit

4. Insert the new lamp unit fully in.

Caution

Neither touch the glass surface of the lamp directly with your hand nor stain it. If you touch it with a bare hand, oil and other substances on your hand may ad- here to the lamp, possibly preventing it from perform- ing as specified and therefore leading to a shortened lamp life, a darkened screen, etc.

5. Close the handle, and tighten the screw.

Tighten the two screws with a ª screwdriver.

6. Attach the light-source lamp cover and tighten the screw.

Tighten the two screws with a ª screwdriver.

Note

When closing the lamp cover, please insert the left side (with the two claws) in first and then ensure that the protruding part found on the reverse side of the cover fits snugly into the hole of the main unit. As this protrusion acts as a switch, misfitting leads to power not being able to flow in.

Image 43

Contents Serial No Model No. FDP-DILA3About burning-in of the D-ILA device About the installation placeFCC Information U.S.A. only Machine Noise INFORMATIONGermany onlyDo not allow any unqualified person to install the unit Safety PrecautionDo not cut off the main plug from this equipment Wire which is coloured green-and-yellow must be conHow To Replace The Fuse Brown LiveViewing conditions Using the screen mode switch functionCare Eplacing the L amp Pecifications Dimensions Pin arrangementAution Acces s ories Ontrols and F eatures Menu C onfigurationFront Side/Top Surface/Left Side Controls and FeaturesControls and Features Connector PanelAlternately*2 Indicator Display on the Control PanelControl Panel on the Projector Stand by light on Operate light on Stand by blinkingTemp Indicator Stand by IndicatorOperate Indicator Volume ª / · buttonsRemote Control’s signal transmitter Remote Control UnitDigital Zoom ª / · buttons Remote Control’s signal transmitter Operate buttonVolume ª / · button Screen buttonLoad the batteries Loading Batteries into the Remote ControlPrecautions for using batteries Open the back coverPrecautions for Installation Installing the ProjectorMounting the Projector Installing the Projector against the ScreenInstalling the Projector Precaution for ceiling-mountProjection Distance and Screen Size Screen installationWhen the remote control unit fails to work properly Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit Using as a wired Remote Control Computer signals Connecting to Various DevicesSignals that can be input into the projector Video signalsHorPixels Ver Lines KHz Connecting to Various Devices Allowable input signals SignalOnnecting to Various Devices Connecting to Computers Connection for controlling more than one projector Control from external devicePower cord supplied Connecting the Power Cord suppliedSelecting the image to be projected Basic Operation ProceduresPower On Basic OperationsAdjusting the Focus RingFocus Remove top cover to access Display using the direct buttonsBasic Operations Adjusting the Sound Volume Power OffFrequently used Convenient Functions Digital zoom DisplayEnlarging the Image Press the Freeze button Turning Off Image and SoundDisplaying a Still Picture Press the Hide button once Vert. Keystone Display Press V-KEYSTONE / to adjust in the vertical directionPress H-KEYSTONE / to adjust in the horizontal direction Removing the Trapezoidal Distortion of the ImagePress the Quick Align Quick Alignment button Using the Quick Alignment functionSelecting the Screen Size Screen size displayMenu Structure Adjustments and Settings Using MenusMenus of the projector have the following structure Submenu Main menuCapture menu Capture start Submenu Adjustments and Settings Using MenusMenu Operation Buttons Procedure for Menu Operation Color temp. menu Menu ConfigurationSet up menu Image adj. menuCapture menu Logo menuPosition menu Decoder menuLanguage menu Capture startOptions menu q Color profile menuInformation menu When no image signal is inputtedPress the Enter or the right Cursor button Editing and Projecting LogoProject the images to be included in your logo Select Logo with the Cursor buttons / Select Horiz. size with the Cursor buttons / Editing and projecting logoSet the menu position as required Select Vert. move with the Cursor buttons / Light source lamp and its lamp time Procedure for lamp replacementAbout lamp replacement Replacing the LampClose the handle, and tighten the screw Replacing the LampRemove the lamp unit Insert the new lamp unit fullyResetting the lamp time Reinstalling the filter Cleaning and Replacing the FilterPull out the power cord from the wall outlet Clean the filterSymptom Probable cause Corrective action TroubleshootingFuzzy TroubleshootingMessage Cause Contents What to do when these messages are displayedWhat to do when these messages are displayed Cooling fan has stopped. Fan locked About warning indicatorsPlease follow the procedures below Action to be taken upon warning indicationsSpecifications Specifications PC 1 terminal SpecificationsPin arrangement Y/C terminal RS-232C IN/OUT terminalHeader Communication SpecificationsCommand Format RS-232C external controlFunction External control command tableOperation mode parameters Character Hex Meaning Operation mode Only Asking command is possibleFaroudja Warranty Statement FDP-DILA3 Theater Optimized Package