Meridian Audio FDP-DILA3 warranty About warning indicators, Cooling fan has stopped. Fan locked

Page 50

Warning Indication

About warning indicators

If something abnormal has occurred in the projector, the warning mode sets on and the abnormality will be indicated by a combina- tion of indicators displayed on the control panel as shown in the following table.

Then, the projector automatically stops projection and runs the cooling fan for about 90 seconds.

No.

Indicator

Warning

LAMP

TEMP

STAND BY

OPERATE

1

Blink

Blink

The light-source lamp does not light up and projection cannot be done.

2

Blink

Blink simultaneously

Blink

The light-source lamp suddenly goes off during projection.

3

Blink

Blink

Circuit operation is abnormal

4

Blink

Blink alternately

Blink

The light-source lamp is misfitted.

5

Blink

The internal temperature is abnormally high.

6

Blink

Blink

The temperature at the air inlets has risen abnormally high.

7

Blink

Blink

Blink

Blink

The cooling fan has stopped. (Fan locked)

*For details on individually blinking indicators, please see page 42.

Action to be taken upon warning indications

Please follow the procedures below.

For No.1-3

No.1 : Unplug from the main power outlet and restart according to the basic operation procedures.

No.2 : After checking if a shock (such as from knocking) has not ocurred during operation, unplug from the main power outlet and restart according to the basic operation procedures.

No.3 : Unplug from the main power outlet and restart according to the basic operation procedures.

For No.4-7

After the STAND BY indicator lights up, pull out the power cord and check the following items one-by one. No.4 : Set the lamp unit in place. Restart according to the basic operation procedures.

No.5 : Check that nothing is blocking the air inlets, and wait until the inside cools down. Restart according to the basic operation procedures.

No.6 : Check the ambient temperature. If it is normal, leave the projector until it cools down. Restart according to the basic operation procedures.

No.7 : Leave the projector until it cools down. Restart according to the basic operation procedures.

If the same warning indication is observed again, after the cooling fan has stopped, ensure the projector goes into the stand-by state with the STAND BY indicator on, unplug the power cord, and call your dealer for repair.

50

Image 50

Contents Model No. FDP-DILA3 Serial NoMachine Noise INFORMATIONGermany only About the installation placeFCC Information U.S.A. only About burning-in of the D-ILA deviceSafety Precaution Do not allow any unqualified person to install the unitBrown Live Wire which is coloured green-and-yellow must be conHow To Replace The Fuse Do not cut off the main plug from this equipmentCare Using the screen mode switch functionViewing conditions Menu C onfiguration Pecifications Dimensions Pin arrangementAution Acces s ories Ontrols and F eatures Eplacing the L ampControls and Features Front Side/Top Surface/Left SideConnector Panel Controls and FeaturesStand by light on Operate light on Stand by blinking Indicator Display on the Control PanelControl Panel on the Projector Alternately*2Volume ª / · buttons Stand by IndicatorOperate Indicator Temp IndicatorRemote Control Unit Remote Control’s signal transmitterScreen button Remote Control’s signal transmitter Operate buttonVolume ª / · button Digital Zoom ª / · buttonsOpen the back cover Loading Batteries into the Remote ControlPrecautions for using batteries Load the batteriesInstalling the Projector Precautions for InstallationPrecaution for ceiling-mount Installing the Projector against the ScreenInstalling the Projector Mounting the ProjectorScreen installation Projection Distance and Screen Size Using as a wired Remote Control Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit When the remote control unit fails to work properly Video signals Connecting to Various DevicesSignals that can be input into the projector Computer signalsSignal Connecting to Various Devices Allowable input signals HorPixels Ver Lines KHzOnnecting to Various Devices Connecting to Computers Control from external device Connection for controlling more than one projectorConnecting the Power Cord supplied Power cord suppliedBasic Operations Basic Operation ProceduresPower On Selecting the image to be projectedBasic Operations Display using the direct buttonsAdjusting the Focus RingFocus Remove top cover to access Power Off Adjusting the Sound VolumeEnlarging the Image Digital zoom DisplayFrequently used Convenient Functions Press the Hide button once Turning Off Image and SoundDisplaying a Still Picture Press the Freeze buttonRemoving the Trapezoidal Distortion of the Image Press V-KEYSTONE / to adjust in the vertical directionPress H-KEYSTONE / to adjust in the horizontal direction Vert. Keystone Display Screen size display Using the Quick Alignment functionSelecting the Screen Size Press the Quick Align Quick Alignment buttonMenus of the projector have the following structure Adjustments and Settings Using MenusMenu Structure Capture menu Capture start Main menuSubmenu Adjustments and Settings Using Menus SubmenuMenu Operation Buttons Procedure for Menu Operation Image adj. menu Menu ConfigurationSet up menu Color temp. menuDecoder menu Logo menuPosition menu Capture menuColor profile menu Capture startOptions menu q Language menuWhen no image signal is inputted Information menuSelect Logo with the Cursor buttons / Editing and Projecting LogoProject the images to be included in your logo Press the Enter or the right Cursor button Select Vert. move with the Cursor buttons / Editing and projecting logoSet the menu position as required Select Horiz. size with the Cursor buttons / Replacing the Lamp Procedure for lamp replacementAbout lamp replacement Light source lamp and its lamp timeInsert the new lamp unit fully Replacing the LampRemove the lamp unit Close the handle, and tighten the screwResetting the lamp time Clean the filter Cleaning and Replacing the FilterPull out the power cord from the wall outlet Reinstalling the filterTroubleshooting Symptom Probable cause Corrective actionTroubleshooting FuzzyWhat to do when these messages are displayed Message Cause ContentsWhat to do when these messages are displayed Action to be taken upon warning indications About warning indicatorsPlease follow the procedures below Cooling fan has stopped. Fan lockedSpecifications Specifications Y/C terminal RS-232C IN/OUT terminal SpecificationsPin arrangement PC 1 terminal RS-232C external control Communication SpecificationsCommand Format HeaderOperation mode Only Asking command is possible External control command tableOperation mode parameters Character Hex Meaning FunctionFaroudja Warranty Statement FDP-DILA3 Theater Optimized Package