Onkyo HT-S6200, 29344937 instruction manual Using Audyssey 2EQ

Page 47

First Time Setup—Continued

Using Audyssey 2EQ™

Notes:

(Asian models) If any of your speakers is 4 ohms, change the Speaker Impedance setting before running the Audyssey 2EQ Room Correction and speaker setup (see page 44).

If the AV receiver is muted, it will be unmuted automatically when the Audyssey 2EQ Room Correction and Speaker Setup starts.

Room correction and speaker setup cannot be performed while a pair of headphones is connected.

It takes about 10 minutes to complete the room correction and speaker setup for three positions. Total measurement time varies depending on the number of speakers.

Do not connect or disconnect any speakers during room correction and speaker setup.

ON/STANDBY

Speaker setup microphone

SETUP MIC

ENTER

1

Turn on the AV receiver.

 

2

Set the speaker setup

 

 

microphone at the Main Listening

 

Position a (page 46), and

 

connect it to the SETUP MIC jack.

 

Audyssey indicator

 

The speaker setting menu appears.

 

If you change these settings, refer to

 

steps 5–6 on “Speaker Settings”

 

(page 44) or step 5 on “Setting the

 

Powered Zone 2” (page 81).

Notes:

Before starting Audyssey 2EQ™ Room Correction and Speaker Setup, arrange the room and connect the speakers as you would for enjoying movies. Changes to the room after auto setup requires you run the auto setup again, as room EQ characteristics may have changed.

When starting the room correction and speaker setup, do not stand between the speakers and microphone, and avoid obstacles blocking the path between speakers and microphone. This will produce inaccurate results.

Position the microphone at ear height of a seated listener with the microphone tip pointed directly at the ceiling using a tripod. Do not hold the microphone in your hand during measurements as this will produce innacurate results.

Make the room as quiet as possible. Background noise can disrupt the room measurements. Close windows, silence cell phones, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices.

Cell phones should be turned off or placed away from all audio electronics during the measurement process as Radio Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use).

3

Press [ENTER].

 

 

The room calibration and speaker setup starts.

Test tones are played through each speaker as Audyssey 2EQ Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measure- ments and do not stand between speakers and the microphone.

Note:

You can cancel the Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

4

When the following display appears,

 

 

move the speaker setup microphone to

 

measurement point b (page 46), and

 

then press [ENTER].

 

 

 

 

 

 

Audyssey 2EQ performs more measurements. This takes a few minutes.

47

Image 47
Contents HT-S6200 Avis Important Safety InstructionsBatteries and Heat Exposure Warning PrecautionsPower Preventing Hearing Loss CautionSpeaker Precautions Package Contents Package Contents Contents Connections FeaturesAmplifier ProcessingFeatures Zone 2 Room Multiroom CapabilityMain Room Front Panel Front & Rear PanelsDisplay Front & Rear PanelsRear Panel VCR/DVR IN/OUT Remote ControlTV/TAPE IN/OUT CBL/SATSubwoofer SKW-770 Speaker PackageSpeaker terminals Speaker PackageKeyhole slots Aiming the Remote Controller Remote ControllerInstalling the Batteries Controlling the AV receiver Remote ControllerEnjoying Home Theater About Home TheaterSpeaker Connection Precautions Connecting the AV receiverConnecting Your Speakers Speaker ConfigurationPush terminals Connecting the AV receiverConnecting the Speaker Cables Terminal postsWall Mounting Using the Rubber Stoppers for a More Stable PlatformUsing the Floor Pads for Subwoofer Bi-amping Speaker Hookup Bi-amping the Front SpeakersAttach the FM antenna, as shown North American models Connecting AntennaConnecting the Indoor FM Antenna Connecting the AM Loop AntennaUsing a TV/FM Antenna Splitter Connecting an Outdoor FM AntennaConnecting an Outdoor AM Antenna AV Cables and Jacks About AV ConnectionsOptical Digital Jacks AV Connection Color Coding Audio Connection Formats Connecting Both Audio & VideoWhich Connections Should I Use? Video Connection FormatsAbout Copyright Protection Connecting Components with HdmiAbout Hdmi Supported Audio FormatsStep Video SignalsAudio Signals Making Hdmi ConnectionsAudio Connection Connecting a TV or ProjectorVideo Connection Connecting a DVD/BD Player Connecting a VCR or DVR for Playback Make the audio connection a Connecting a VCR or DVR for RecordingComponent Video in 2 CBL/SAT Make the video connection a Make the audio connection a Connecting a Camcorder, Game Console, or Other DeviceConnecting a Portable Audio player CD Player or Turntable MM with Built-in Phono Preamp Step Connecting a CD Player or TurntableConnecting a Cassette, CDR, MiniDisc, or DAT Recorder If Your iPod or iPhone Don’t Support Video Connecting an RI DockNot all iPod models output video If Your iPod or iPhone Supports VideoConnecting a Dock with the Universal Port connector Direct Change Connecting Onkyo u ComponentsConnecting the Power Cord Auto Power On/StandbyUp and Running in a Few Easy Steps Turning On the AV receiverTurning On and Standby Press the Setup button First Time SetupHdmi Input Setup Followed by the Setup buttonComponent Video Input Setup First Time SetupSetup closes Digital Input SetupUse the Up and Down q/ w but Speaker SettingsButtons to select Sp Type, Use the Left and Right e/ rChanging the Input Display Second measurement point Audyssey 2EQ Room Correction and Speaker SetupMeasurement Positions First measurement pointUsing Audyssey 2EQ Using a Powered Subwoofer Error MessagesTo Retry the Room Correction and Speaker Setup Changing the Speaker Settings ManuallyBasic AV receiver Operation Select a listening mode and enjoyBasic Operations Bass Adjusting the Bass & TrebleBasic Operations Displaying Source InformationUsing Headphones Setting the Display BrightnessMuting the AV receiver Using the Sleep Timer Auto default Using the Music OptimizerSpecifying the Digital Signal Format Use the Left and Right e/r AM/FM Frequency Step SetupListening to the Radio North American models Asian modelsListening to the Radio Using the TunerTuning into AM/FM Radio Stations Listening to the RadioDisplaying AM/FM Radio Information Tuning into Stations by FrequencySelecting Presets Presetting AM/FM StationsDeleting Presets Made for About the UP-A1 series DockCompatible iPod/iPhone models Putting Your iPod/iPhone in the DockControlling iPod/iPhone Using Your iPod or iPhone models Alarm ClockCharging Your iPod or iPhone models Battery UP-A1 series Dock for iPod/iPhoneStatus messages Recording Selecting on the AV receiver Using the Listening ModesSelecting with the Remote Controller Selecting Listening ModesMono/Multiplex Sources Using the Listening ModesListening Modes Available for Each Source Format Available Listening Modes Stereo SourceDTS/DTS-HD Channel SourcesDTS-ES DTS-ES Discrete/Matrix SourcesAbout the Listening Modes Onkyo Original DSP Modes Speaker Setup Advanced SetupCommon Procedures in Setup Menu Sp Distance Speaker Distance Advanced SetupUse the Down w button to select Ch, and then use the Left Equalizer Equalizer SettingsLeft and Right e/ r buttons to adjust the level at that Level Cal Speaker Levels CalibrationDolby EX Audio AdjustAudio Adjust Mux/Mono Multiplex/Mono DolbyAudyssey D Theater-DimensionalDTS Neo6 Music Using the Audio Settings Speaker Layout Audyssey Dynamic VolumeCinemaFILTER Music OptimizerAssigning Listening Modes to Input Sources Sync Source SetupIntelliVolume Volume Setup Miscellaneous Volume SetupTuner Hardware SetupRemote ID Hdmi Ctrl Power CtrlLipSync XvColorZone Connecting ZoneConnecting Your Zone 2 Speakers Directly to the AV receiver Connecting Your Zone 2 Speakers to an Amp in ZoneIf you’ve connected your Zone 2 speakers to the AV Setting the Powered ZoneSettings, and then press Enter Use the Up and Down q/wControlling Zone 2 from the AV receiver Using ZoneControlling Zone 2 with the Remote Controller Muting Zones Adjusting the Volume of ZonesControlling Other Components Preprogrammed Remote Control CodesEntering Remote Control Codes Controlling Other Components Remote Control Codes for Onkyo Components Connected via uResetting Remote Mode Buttons Resetting the Remote ControllerControlling a TV Controlling a DVD Player, or DVD Recorder Controlling a VCR or PVR Controlling a Satellite Receiver or Cable Receiver Disc +/- button Controlling a CD PlayerPlaylist e/r button When Using an RI DockControlling an RI Dock Reverse Play t button Controlling a Cassette RecorderPrevious and Next 7/6 buttons Rewind and Fast Forward 5/4 buttonsTroubleshooting Troubleshooting There’s no video Remote controller doesn’t workCan’t control other components There’s no soundU functions don’t work Sound changes when I connect my headphonesCan’t record How do I change the language of a multiplex sourceTuner Section SpecificationsAmplifier Section Video SectionCenter Speaker SKC-670 SpecificationsPowered Subwoofer SKW-770 Front Speaker SKF-670Memo 3 4 4 9 3

HT-S6200, 29344937 specifications

The Onkyo HT-S6200 is a versatile and powerful home theater system that delivers an impressive audio experience for music and movie enthusiasts alike. One of its standout features is the 7.1-channel surround sound configuration, which creates an immersive sound environment, enveloping listeners with crystal-clear audio. This configuration is especially effective in large rooms, providing an enveloping sound that enhances the viewing experience for everything from action-packed movies to nuanced dramas.

The system includes a powerful AV receiver, model TX-SR313, boasting a variety of connectivity options. With six HDMI inputs, it allows users to connect multiple devices such as Blu-ray players, gaming consoles, and streaming devices easily. The receiver supports 4K video pass-through, making it future-proof for high-definition content and ideal for users looking to enjoy the latest in home entertainment.

Another key aspect of the HT-S6200 is its implementation of Dolby TrueHD and DTS-HD Master Audio technologies. These formats deliver lossless audio, ensuring that soundtracks and sound effects are reproduced with stunning fidelity, replicating a cinema-like experience at home. Furthermore, the system features Dolby Pro Logic IIz, which enhances the surround sound experience by creating an additional layer of depth through front height channels.

The Onkyo HT-S6200 also integrates a user-friendly graphical user interface, making setup and operation straightforward. High-quality speaker components, including a powered subwoofer with a 12-inch driver, produce deep, powerful bass, providing an excellent anchor for the overall sound stage. The satellite speakers are designed to deliver clear midrange and high frequencies, ensuring every dialogue and musical note is distinct and engaging.

With its elegant design, the HT-S6200 fits seamlessly into any home décor, while also providing robust performance. The system also supports Onkyo’s exclusive AccuEQ room acoustic calibration technology, which automatically adjusts the sound settings to suit the specific acoustics of a room. This feature enhances the listening experience by optimizing audio playback according to the user’s environment.

In summary, the Onkyo HT-S6200 combines advanced audio technologies, versatile connectivity options, and user-friendly features to create a compelling home theater system. Whether enjoying a thrilling movie night or listening to music, this system promises to elevate any audio experience, making it a worthy investment for any home entertainment enthusiast.