Onkyo 29344937, HT-S6200 Error Messages, To Retry the Room Correction and Speaker Setup

Page 48

First Time Setup—Continued

5

When the following display appears,

 

 

move the speaker setup microphone to

 

measurement point c (page 46), and

 

then press [ENTER].

 

 

 

 

 

 

Audyssey 2EQperforms more measurements.

This takes a few minutes.

When the measurements are complete, the results are calculated and saved automatically.

6

When the room correction and speaker

 

 

setup is complete, disconnect the

 

speaker setup microphone.

 

 

 

 

 

 

 

 

 

 

 

 

Notes:

When the room correction and speaker setup is complete, the Equalizer Settings (page 70) will be set to “Audyssey” and the “Dynamic EQ” (page 72) will be set to “On”.

You can cancel the Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

Error Messages

While the room correction and speaker setup is in progress, one of the following error messages may appear:

Ambient noise is too high

This message appears if there’s too much background noise and the measurements cannot be performed properly. Remove the source of the noise and try again.

Speaker Detect Errors

This message appears if one of the speaker-related errors below occurs.

One of the front speakers has not been detected.

One of the surround speakers has not been detected.

The surround back speakers have been detected but the surround speakers haven’t.

The right surround back speaker has been detected but the left surround back speaker hasn’t.

Write Error

This message appears if saving fails.

Mismatch Error

This message appears if a speaker that was detected during the 1st measurement is not detected during the 2nd or 3rd measurements. If this message appears, check your speaker connections, and then try again.

To Retry the Room Correction and Speaker Setup

Press the [ENTER] button.

Make sure speakers that cannot be detected are connected properly.

Changing the Speaker Settings Manually

If you wish to make changes to the settings found during the automatic speaker setup, follow the directions on pages 68–70.

Using a Powered Subwoofer

If you’re using a powered subwoofer, as it outputs very low-frequency sound and its position is usually low down, it may not be detected by the Audyssey 2EQ Room Correction and Speaker Setup. When “Subwoofer” is set to “No” in the “2-2.Sp Config (Speaker Configuration)” (page 68), increase the subwoofer’s volume, select its highest crossover frequency, and then try running the Audyssey 2EQ Room Correction and Speaker Setup again. Note that if the volume is set too high and the sound distorts, it may not be detected, so use an appropriate volume level.

48

Image 48
Contents HT-S6200 Important Safety Instructions AvisPrecautions PowerPreventing Hearing Loss Caution Batteries and Heat Exposure WarningSpeaker Precautions Package Contents Package Contents Contents Features AmplifierProcessing ConnectionsFeatures Multiroom Capability Main RoomZone 2 Room Front & Rear Panels Front PanelFront & Rear Panels DisplayRear Panel Remote Control TV/TAPE IN/OUTCBL/SAT VCR/DVR IN/OUTSpeaker Package Subwoofer SKW-770Speaker Package Keyhole slotsSpeaker terminals Remote Controller Installing the BatteriesAiming the Remote Controller Remote Controller Controlling the AV receiverAbout Home Theater Enjoying Home TheaterConnecting the AV receiver Connecting Your SpeakersSpeaker Configuration Speaker Connection PrecautionsConnecting the AV receiver Connecting the Speaker CablesTerminal posts Push terminalsUsing the Rubber Stoppers for a More Stable Platform Using the Floor Pads for SubwooferWall Mounting Bi-amping the Front Speakers Bi-amping Speaker HookupConnecting Antenna Connecting the Indoor FM AntennaConnecting the AM Loop Antenna Attach the FM antenna, as shown North American modelsConnecting an Outdoor FM Antenna Connecting an Outdoor AM AntennaUsing a TV/FM Antenna Splitter About AV Connections Optical Digital Jacks AV Connection Color CodingAV Cables and Jacks Connecting Both Audio & Video Which Connections Should I Use?Video Connection Formats Audio Connection FormatsConnecting Components with Hdmi About HdmiSupported Audio Formats About Copyright ProtectionVideo Signals Audio SignalsMaking Hdmi Connections StepConnecting a TV or Projector Video ConnectionAudio Connection Connecting a DVD/BD Player Connecting a VCR or DVR for Playback Connecting a VCR or DVR for Recording Make the audio connection aComponent Video in 2 CBL/SAT Connecting a Camcorder, Game Console, or Other Device Connecting a Portable Audio playerMake the video connection a Make the audio connection a Connecting a CD Player or Turntable CD Player or Turntable MM with Built-in Phono Preamp StepConnecting a Cassette, CDR, MiniDisc, or DAT Recorder Connecting an RI Dock Not all iPod models output videoIf Your iPod or iPhone Supports Video If Your iPod or iPhone Don’t Support VideoConnecting a Dock with the Universal Port connector Connecting Onkyo u Components Connecting the Power CordAuto Power On/Standby Direct ChangeTurning On the AV receiver Turning On and StandbyUp and Running in a Few Easy Steps First Time Setup Hdmi Input SetupFollowed by the Setup button Press the Setup buttonFirst Time Setup Component Video Input SetupDigital Input Setup Setup closesSpeaker Settings Buttons to select Sp Type,Use the Left and Right e/ r Use the Up and Down q/ w butChanging the Input Display Audyssey 2EQ Room Correction and Speaker Setup Measurement PositionsFirst measurement point Second measurement pointUsing Audyssey 2EQ Error Messages To Retry the Room Correction and Speaker SetupChanging the Speaker Settings Manually Using a Powered SubwooferSelect a listening mode and enjoy Basic OperationsBasic AV receiver Operation Adjusting the Bass & Treble Basic OperationsDisplaying Source Information BassSetting the Display Brightness Muting the AV receiver Using the Sleep TimerUsing Headphones Using the Music Optimizer Specifying the Digital Signal FormatAuto default AM/FM Frequency Step Setup Listening to the RadioNorth American models Asian models Use the Left and Right e/rUsing the Tuner Tuning into AM/FM Radio StationsListening to the Radio Listening to the RadioTuning into Stations by Frequency Displaying AM/FM Radio InformationPresetting AM/FM Stations Deleting PresetsSelecting Presets About the UP-A1 series Dock Compatible iPod/iPhone modelsPutting Your iPod/iPhone in the Dock Made forUsing Your iPod or iPhone models Alarm Clock Charging Your iPod or iPhone models BatteryUP-A1 series Dock for iPod/iPhone Controlling iPod/iPhoneStatus messages Recording Using the Listening Modes Selecting with the Remote ControllerSelecting Listening Modes Selecting on the AV receiverUsing the Listening Modes Listening Modes Available for Each Source FormatMono/Multiplex Sources Stereo Source Available Listening ModesChannel Sources DTS/DTS-HDDTS-ES Discrete/Matrix Sources DTS-ESAbout the Listening Modes Onkyo Original DSP Modes Advanced Setup Common Procedures in Setup MenuSpeaker Setup Advanced Setup Sp Distance Speaker DistanceEqualizer Equalizer Settings Left and Right e/ r buttons to adjust the level at thatLevel Cal Speaker Levels Calibration Use the Down w button to select Ch, and then use the LeftAudio Adjust Audio Adjust Mux/Mono Multiplex/MonoDolby Dolby EXD Theater-Dimensional DTS Neo6 MusicAudyssey Using the Audio Settings Audyssey Dynamic Volume CinemaFILTERMusic Optimizer Speaker LayoutAssigning Listening Modes to Input Sources Source Setup IntelliVolumeSync Miscellaneous Volume Setup Volume SetupHardware Setup Remote IDTuner Power Ctrl LipSyncXvColor Hdmi CtrlConnecting Zone Connecting Your Zone 2 Speakers Directly to the AV receiverConnecting Your Zone 2 Speakers to an Amp in Zone ZoneSetting the Powered Zone Settings, and then press EnterUse the Up and Down q/w If you’ve connected your Zone 2 speakers to the AVUsing Zone Controlling Zone 2 with the Remote ControllerControlling Zone 2 from the AV receiver Adjusting the Volume of Zones Muting ZonesPreprogrammed Remote Control Codes Entering Remote Control CodesControlling Other Components Remote Control Codes for Onkyo Components Connected via u Resetting Remote Mode ButtonsResetting the Remote Controller Controlling Other ComponentsControlling a TV Controlling a DVD Player, or DVD Recorder Controlling a VCR or PVR Controlling a Satellite Receiver or Cable Receiver Controlling a CD Player Disc +/- buttonWhen Using an RI Dock Controlling an RI DockPlaylist e/r button Controlling a Cassette Recorder Previous and Next 7/6 buttonsRewind and Fast Forward 5/4 buttons Reverse Play t buttonTroubleshooting Troubleshooting Remote controller doesn’t work Can’t control other componentsThere’s no sound There’s no videoSound changes when I connect my headphones Can’t recordHow do I change the language of a multiplex source U functions don’t workSpecifications Amplifier SectionVideo Section Tuner SectionSpecifications Powered Subwoofer SKW-770Front Speaker SKF-670 Center Speaker SKC-670Memo 3 4 4 9 3

HT-S6200, 29344937 specifications

The Onkyo HT-S6200 is a versatile and powerful home theater system that delivers an impressive audio experience for music and movie enthusiasts alike. One of its standout features is the 7.1-channel surround sound configuration, which creates an immersive sound environment, enveloping listeners with crystal-clear audio. This configuration is especially effective in large rooms, providing an enveloping sound that enhances the viewing experience for everything from action-packed movies to nuanced dramas.

The system includes a powerful AV receiver, model TX-SR313, boasting a variety of connectivity options. With six HDMI inputs, it allows users to connect multiple devices such as Blu-ray players, gaming consoles, and streaming devices easily. The receiver supports 4K video pass-through, making it future-proof for high-definition content and ideal for users looking to enjoy the latest in home entertainment.

Another key aspect of the HT-S6200 is its implementation of Dolby TrueHD and DTS-HD Master Audio technologies. These formats deliver lossless audio, ensuring that soundtracks and sound effects are reproduced with stunning fidelity, replicating a cinema-like experience at home. Furthermore, the system features Dolby Pro Logic IIz, which enhances the surround sound experience by creating an additional layer of depth through front height channels.

The Onkyo HT-S6200 also integrates a user-friendly graphical user interface, making setup and operation straightforward. High-quality speaker components, including a powered subwoofer with a 12-inch driver, produce deep, powerful bass, providing an excellent anchor for the overall sound stage. The satellite speakers are designed to deliver clear midrange and high frequencies, ensuring every dialogue and musical note is distinct and engaging.

With its elegant design, the HT-S6200 fits seamlessly into any home décor, while also providing robust performance. The system also supports Onkyo’s exclusive AccuEQ room acoustic calibration technology, which automatically adjusts the sound settings to suit the specific acoustics of a room. This feature enhances the listening experience by optimizing audio playback according to the user’s environment.

In summary, the Onkyo HT-S6200 combines advanced audio technologies, versatile connectivity options, and user-friendly features to create a compelling home theater system. Whether enjoying a thrilling movie night or listening to music, this system promises to elevate any audio experience, making it a worthy investment for any home entertainment enthusiast.