InFocus IN3118HD manual Bottom view, DLP Projector - User’s Manual

Page 12

DLP Projector – User’s Manual

Bottom view

ITEM	LABEL	DESCRIPTION	SEE PAGE:

1.	Leveling foot	Rotate leveling foot to adjust angle position.	10

2.	Ceiling support holes	Only use with an InFocus ceiling mount system (p/n PRJ-MNT-UNIV).
2.	Ceiling support holes	See your InFocus dealer or go to www.infocusstore.com.
		See your InFocus dealer or go to www.infocusstore.com.
3.	Elevator foot	Elevator foot drops down when elevator button is
3.	Elevator foot	pushed.	10
		pushed.
4.	Elevator button	Push to release elevator foot.
4.	Elevator button	Push to release elevator foot.

Note:

When installing, ensure that you use only UL Listed ceiling mounts.

For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw depth of 12 mm (0.47inch).

The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount load capacity must exceed the weight of the installed equipment, and as an additional precaution be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a period of 60 seconds.

– 5 –

Image 12

Contents Page Copyright DisclaimerTrademark Recognition Important Safety Information Symbols UsedGeneral Safety Information IN3118HD User’s ManualProjector Installation Notice Power SafetyPreface Cleaning the Projector Symbol ExplanationsAbout this Manual Replacing the LampSETUP AND OPERATION ON-SCREEN DISPLAY OSD MENU SETTINGSMAINTENANCE AND SECURITY TROUBLESHOOTINGPROJECTOR DIMENSIONS SAFETY CERTIFICATIONSPROJECTION DISTANCE VS. PROJECTION SIZE TIMING MODE TABLEPacking Checklist GETTING STARTEDDLP Projector - User’s Manual Front-right View Views of Projector PartsLABEL DESCRIPTIONTop view-On-screen Display OSD buttons and LEDs see LED Error Messages on pageError code see LED Error Messages on page Rear view LABELDESCRIPTION SEE PAGEBottom view Remote Control Parts Adjust overscan SETUP AND OPERATION Inserting the Remote Control BatteriesStarting and Shutting down the Projector Adjusting the Projector Level Adjusting the Zoom ring, Focus and Keystone Adjusting the Volume 1. Press the Volume but- tons on the projector or the remote control2. Use the Vol +/- buttons on the projector or the remote control The volume control appears on the displayON-SCREEN DISPLAY OSD MENU SETTINGS Navigating the OSDOSD Menu Controls Setting the OSD Language Set the OSD language to your preference before continuing2. Press the cursor button until Language is highlighted 3. Press the cursor button until the language you want is selectedOSD Menu Overview SETUP BasicSETUP Advanced PICTURE BasicPICTUREBasic Menu PICTUREAdvanced Menu HSG Adjustment Press the ENTER/SELECT button to enter the HSG Adjustment sub menuDISPLAY Menu Press to change values for settingsSee PC Detail Adjustment on page PC Detail Adjustment SETUPBasic Menu Menu Settings SourcePress the ENTER/SELECT button to enter the Menu Settings sub menu Press the ENTER/SELECT button to enter the Source sub menuLan Control Settings Network State DLP Projector - User’s Manual Preparing Email Alerts Select the alert conditions by checking the desired boxes SETUPAdvanced Menu Audio LampPress the ENTER/SELECT button to enter the Audio sub menu Press the ENTER/SELECT button to enter the Lamp sub menuHDMI Closed CaptionPress the ENTER/SELECT button to enter the HDMI sub menu Press the ENTER/SELECT button to enter the Closed Caption sub menuPresentation Timer STATUS Menu MAINTENANCE AND SECURITY Replacing the Projection LampRemove the single screw on the lamp compartment cover Remove the lamp com- partment coverRemove the three screws from the lamp module Lift the module handle up6. Pull firmly on the module handle to remove the lamp module Cleaning the Lens Cleaning the CaseCleaning the Projector TROUBLESHOOTING Common Problems and SolutionsTips for Troubleshooting LED Error Messages Image ProblemsProblem No image appears on the screen Problem The image is blurredLamp Problems Remote Control ProblemsProblem The image is streaked Problem The image is flat with no contrastAudio Problems Having the Projector ServicedProblem There is no sound Problem The sound is distortedHDMI Q & A Q. How do I run HDMI cables longer than 10 meters?Q. How can I tell if a cable is an HDMI certified cable? SPECIFICATIONS SpecificationsModel Display type Native Resolution Projection distance Safety certification Operation temperature Dimensions W x D x HProjection Distance and Size Table Projection Distance vs. Projection Size169 SCREEN PROJECTION DISTANCETiming Mode Table H-S YNCV-S YNC HDMIDLP Projector - User’s Manual Projector Dimensions Safety Certifications REGULATORY COMPLIANCEFCC Warning Canada