InFocus manual IN3118HD User’s Manual, Remove the single screw on the lamp compartment cover

Page 41
Remove the single screw on the lamp compartment cover.

IN3118HD User’s Manual

2.

3.

4.

5.

Remove the single screw on the lamp compartment cover.

Remove the lamp com- partment cover.

Remove the three screws from the lamp module.

Lift the module handle up.

– 34 –

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Page Trademark Recognition CopyrightDisclaimer Symbols Used Important Safety InformationGeneral Safety Information IN3118HD User’s ManualPreface Projector Installation NoticePower Safety Symbol Explanations Cleaning the ProjectorAbout this Manual Replacing the LampON-SCREEN DISPLAY OSD MENU SETTINGS SETUP AND OPERATIONMAINTENANCE AND SECURITY TROUBLESHOOTINGSAFETY CERTIFICATIONS PROJECTOR DIMENSIONSPROJECTION DISTANCE VS. PROJECTION SIZE TIMING MODE TABLEDLP Projector - User’s Manual Packing ChecklistGETTING STARTED Views of Projector Parts Front-right ViewLABEL DESCRIPTIONError code see LED Error Messages on page Top view-On-screen Display OSD buttons and LEDssee LED Error Messages on page LABEL Rear viewDESCRIPTION SEE PAGEBottom view Remote Control Parts Adjust overscan Inserting the Remote Control Batteries SETUP AND OPERATIONStarting and Shutting down the Projector Adjusting the Projector Level Adjusting the Zoom ring, Focus and Keystone 1. Press the Volume but- tons on the projector or the remote control Adjusting the Volume2. Use the Vol +/- buttons on the projector or the remote control The volume control appears on the displayOSD Menu Controls ON-SCREEN DISPLAY OSD MENU SETTINGSNavigating the OSD Set the OSD language to your preference before continuing Setting the OSD Language2. Press the cursor button until Language is highlighted 3. Press the cursor button until the language you want is selectedSETUP Basic OSD Menu OverviewSETUP Advanced PICTURE BasicPICTUREBasic Menu PICTUREAdvanced Menu Press the ENTER/SELECT button to enter the HSG Adjustment sub menu HSG AdjustmentSee PC Detail Adjustment on page DISPLAY MenuPress to change values for settings PC Detail Adjustment SETUPBasic Menu Source Menu SettingsPress the ENTER/SELECT button to enter the Menu Settings sub menu Press the ENTER/SELECT button to enter the Source sub menuLan Control Settings Network State DLP Projector - User’s Manual Preparing Email Alerts Select the alert conditions by checking the desired boxes SETUPAdvanced Menu Lamp AudioPress the ENTER/SELECT button to enter the Audio sub menu Press the ENTER/SELECT button to enter the Lamp sub menuClosed Caption HDMIPress the ENTER/SELECT button to enter the HDMI sub menu Press the ENTER/SELECT button to enter the Closed Caption sub menuPresentation Timer STATUS Menu Replacing the Projection Lamp MAINTENANCE AND SECURITYRemove the lamp com- partment cover Remove the single screw on the lamp compartment coverRemove the three screws from the lamp module Lift the module handle up6. Pull firmly on the module handle to remove the lamp module Cleaning the Projector Cleaning the LensCleaning the Case Tips for Troubleshooting TROUBLESHOOTINGCommon Problems and Solutions Image Problems LED Error MessagesProblem No image appears on the screen Problem The image is blurredRemote Control Problems Lamp ProblemsProblem The image is streaked Problem The image is flat with no contrastHaving the Projector Serviced Audio ProblemsProblem There is no sound Problem The sound is distortedQ. How can I tell if a cable is an HDMI certified cable? HDMI Q & AQ. How do I run HDMI cables longer than 10 meters? Specifications SPECIFICATIONSModel Display type Native Resolution Projection distance Safety certification Operation temperature Dimensions W x D x HProjection Distance vs. Projection Size Projection Distance and Size Table169 SCREEN PROJECTION DISTANCEH-S YNC Timing Mode TableV-S YNC HDMIH-S YNC Projector Dimensions REGULATORY COMPLIANCE Safety CertificationsFCC Warning Canada
Top Page Image Contents