InFocus IN3118HD manual LED Error Messages, Image Problems, Temp Led, Problem The image is blurred

Page 45

LED Error Messages

IN3118HD User’s Manual

LED Error Messages

ERROR CODE MESSAGES	POWER LED	LAMP / READY LED	TEMP LED

Powered on	Solid Green	Solid Red	OFF

Powering up	Solid Green	Flashing Red	OFF

Cooling down	Solid Green	Flashing Red	OFF

Over Temperature	OFF	OFF	Solid Red

Thermal Break Sensor error	Flashes Green 4x	Flashes Green 4x	OFF

Lamp error/Color wheel control error	Flashes Green 5x	OFF	OFF

Lamp End of lamp life detected	Flashes Green 5x	Flashes Green 3x	OFF

Burner Fan error	Flashes Green 6x	Flashes Green 1x	OFF

Lamp Fan error	Flashes Green 6x	Flashes Green 2x	OFF

Power Fan error	Flashes Green 6x	Flashes Green 3x	OFF

DMD Fan error	Flashes Green 6x	Flashes Green 4x	OFF

Case Open	Flashes Green 7x	OFF	OFF

DMD error/Ignition failed	Flashes Green 8x	OFF	OFF

Color wheel error	Flashes Green 9x	OFF	OFF

In the event of an error, please disconnect the AC power cord and wait for one (1) minute before re- starting the projector. If the POWER or LAMP LEDs are still blinking or the TEMP LED is lit, contact InFocus Technical Support at www.infocus.com/support.

Image Problems

Problem: No image appears on the screen

1.Verify the settings on your notebook or desktop PC.

2.Turn off all equipment and power up again in the correct order.

3.Many laptops do not automatically turn on their external video port when a projector is connected. Usually a key combination like FN + F8 or CRT/LCD key turns the external display on and off. Locate a function key labeled CRT/LCD or function key with a monitor symbol. Press FN and the labeled function key simultaneously.

Problem: The image is blurred

1.Adjust the Focus on the projector.

2.Press the Auto Image button on the remote control or the Re-sync button on the keypad.

3.Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range.

4.Check that the projector lens is clean.

Problem: The image is wider at the top or bottom (trapezoid effect)

1.Position the projector so it is as perpendicular to the screen as possible.

2.Use the Keystone button on the remote control or projector to correct the problem.

Problem: The image is reversed

Check the Projection setting on the Setup >> Basic menu of the OSD.

– 38 –

Image 45

Contents Page Copyright DisclaimerTrademark Recognition Symbols Used Important Safety InformationGeneral Safety Information IN3118HD User’s ManualProjector Installation Notice Power SafetyPreface Symbol Explanations Cleaning the ProjectorAbout this Manual Replacing the LampON-SCREEN DISPLAY OSD MENU SETTINGS SETUP AND OPERATIONMAINTENANCE AND SECURITY TROUBLESHOOTINGSAFETY CERTIFICATIONS PROJECTOR DIMENSIONSPROJECTION DISTANCE VS. PROJECTION SIZE TIMING MODE TABLEPacking Checklist GETTING STARTEDDLP Projector - User’s Manual Views of Projector Parts Front-right ViewLABEL DESCRIPTIONTop view-On-screen Display OSD buttons and LEDs see LED Error Messages on pageError code see LED Error Messages on page LABEL Rear viewDESCRIPTION SEE PAGEBottom view Remote Control Parts Adjust overscan Inserting the Remote Control Batteries SETUP AND OPERATIONStarting and Shutting down the Projector Adjusting the Projector Level Adjusting the Zoom ring, Focus and Keystone 1. Press the Volume but- tons on the projector or the remote control Adjusting the Volume2. Use the Vol +/- buttons on the projector or the remote control The volume control appears on the displayON-SCREEN DISPLAY OSD MENU SETTINGS Navigating the OSDOSD Menu Controls Set the OSD language to your preference before continuing Setting the OSD Language2. Press the cursor button until Language is highlighted 3. Press the cursor button until the language you want is selectedSETUP Basic OSD Menu OverviewSETUP Advanced PICTURE BasicPICTUREBasic Menu PICTUREAdvanced Menu Press the ENTER/SELECT button to enter the HSG Adjustment sub menu HSG AdjustmentDISPLAY Menu Press to change values for settingsSee PC Detail Adjustment on page PC Detail Adjustment SETUPBasic Menu Source Menu SettingsPress the ENTER/SELECT button to enter the Menu Settings sub menu Press the ENTER/SELECT button to enter the Source sub menuLan Control Settings Network State DLP Projector - User’s Manual Preparing Email Alerts Select the alert conditions by checking the desired boxes SETUPAdvanced Menu Lamp AudioPress the ENTER/SELECT button to enter the Audio sub menu Press the ENTER/SELECT button to enter the Lamp sub menuClosed Caption HDMIPress the ENTER/SELECT button to enter the HDMI sub menu Press the ENTER/SELECT button to enter the Closed Caption sub menuPresentation Timer STATUS Menu Replacing the Projection Lamp MAINTENANCE AND SECURITYRemove the lamp com- partment cover Remove the single screw on the lamp compartment coverRemove the three screws from the lamp module Lift the module handle up6. Pull firmly on the module handle to remove the lamp module Cleaning the Lens Cleaning the CaseCleaning the Projector TROUBLESHOOTING Common Problems and SolutionsTips for Troubleshooting Image Problems LED Error MessagesProblem No image appears on the screen Problem The image is blurredRemote Control Problems Lamp ProblemsProblem The image is streaked Problem The image is flat with no contrastHaving the Projector Serviced Audio ProblemsProblem There is no sound Problem The sound is distortedHDMI Q & A Q. How do I run HDMI cables longer than 10 meters?Q. How can I tell if a cable is an HDMI certified cable? Specifications SPECIFICATIONSModel Display type Native Resolution Projection distance Safety certification Operation temperature Dimensions W x D x HProjection Distance vs. Projection Size Projection Distance and Size Table169 SCREEN PROJECTION DISTANCEH-S YNC Timing Mode TableV-S YNC HDMIH-S YNC Projector Dimensions REGULATORY COMPLIANCE Safety CertificationsFCC Warning Canada