InFocus IN3118HD manual About this Manual, Replacing the Lamp, Cleaning the Projector

Page 5

Replacing the Lamp

IN3118HD User’s Manual

Replacing the Lamp

Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 33 for clear and safe instructions for this procedure. Before replacing the lamp:

¾Unplug the power cord.

¾Allow the lamp to cool for about one hour.

Cleaning the Projector

¾Unplug the power cord before cleaning. See Cleaning the Projector on page 36.

¾Allow the lamp to cool for about one hour.

Regulatory Warnings

Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section on page 47.

Important Recycle Instructions:

Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at www.eiae.org. For lamp specific

disposal information check www.lamperecycle.org.

Symbol Explanations

DISPOSAL: Do not use household or municipal waste collection services for disposal of electrical and electronic equipment. EU countries require the use of separate recycling collection services.

About this Manual

This manual is intended for end users and describes how to install and operate the DLP projector. Wher- ever possible, relevant information—such as an illustration and its description—has been kept on one page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print sections that are relevant to your needs.

— iv —

Image 5

Contents Page Trademark Recognition CopyrightDisclaimer Symbols Used Important Safety InformationGeneral Safety Information IN3118HD User’s ManualPreface Projector Installation NoticePower Safety Symbol Explanations Cleaning the ProjectorAbout this Manual Replacing the LampON-SCREEN DISPLAY OSD MENU SETTINGS SETUP AND OPERATIONMAINTENANCE AND SECURITY TROUBLESHOOTINGSAFETY CERTIFICATIONS PROJECTOR DIMENSIONSPROJECTION DISTANCE VS. PROJECTION SIZE TIMING MODE TABLEDLP Projector - User’s Manual Packing ChecklistGETTING STARTED Views of Projector Parts Front-right ViewLABEL DESCRIPTIONError code see LED Error Messages on page Top view-On-screen Display OSD buttons and LEDssee LED Error Messages on page LABEL Rear viewDESCRIPTION SEE PAGEBottom view Remote Control Parts Adjust overscan Inserting the Remote Control Batteries SETUP AND OPERATIONStarting and Shutting down the Projector Adjusting the Projector Level Adjusting the Zoom ring, Focus and Keystone 1. Press the Volume but- tons on the projector or the remote control Adjusting the Volume2. Use the Vol +/- buttons on the projector or the remote control The volume control appears on the displayOSD Menu Controls ON-SCREEN DISPLAY OSD MENU SETTINGSNavigating the OSD Set the OSD language to your preference before continuing Setting the OSD Language2. Press the cursor button until Language is highlighted 3. Press the cursor button until the language you want is selectedSETUP Basic OSD Menu OverviewSETUP Advanced PICTURE BasicPICTUREBasic Menu PICTUREAdvanced Menu Press the ENTER/SELECT button to enter the HSG Adjustment sub menu HSG AdjustmentSee PC Detail Adjustment on page DISPLAY MenuPress to change values for settings PC Detail Adjustment SETUPBasic Menu Source Menu SettingsPress the ENTER/SELECT button to enter the Menu Settings sub menu Press the ENTER/SELECT button to enter the Source sub menuLan Control Settings Network State DLP Projector - User’s Manual Preparing Email Alerts Select the alert conditions by checking the desired boxes SETUPAdvanced Menu Lamp AudioPress the ENTER/SELECT button to enter the Audio sub menu Press the ENTER/SELECT button to enter the Lamp sub menuClosed Caption HDMIPress the ENTER/SELECT button to enter the HDMI sub menu Press the ENTER/SELECT button to enter the Closed Caption sub menuPresentation Timer STATUS Menu Replacing the Projection Lamp MAINTENANCE AND SECURITYRemove the lamp com- partment cover Remove the single screw on the lamp compartment coverRemove the three screws from the lamp module Lift the module handle up6. Pull firmly on the module handle to remove the lamp module Cleaning the Projector Cleaning the LensCleaning the Case Tips for Troubleshooting TROUBLESHOOTINGCommon Problems and Solutions Image Problems LED Error MessagesProblem No image appears on the screen Problem The image is blurredRemote Control Problems Lamp ProblemsProblem The image is streaked Problem The image is flat with no contrastHaving the Projector Serviced Audio ProblemsProblem There is no sound Problem The sound is distortedQ. How can I tell if a cable is an HDMI certified cable? HDMI Q & AQ. How do I run HDMI cables longer than 10 meters? Specifications SPECIFICATIONSModel Display type Native Resolution Projection distance Safety certification Operation temperature Dimensions W x D x HProjection Distance vs. Projection Size Projection Distance and Size Table169 SCREEN PROJECTION DISTANCEH-S YNC Timing Mode TableV-S YNC HDMIH-S YNC Projector Dimensions REGULATORY COMPLIANCE Safety CertificationsFCC Warning Canada