InFocus manual Setting the OSD Language, IN3118HD User’s Manual

Page 21

IN3118HD User’s Manual

Setting the OSD Language

Set the OSD language to your preference before continuing.

1.Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic.

2.Press the cursor ▲▼ button until Language is highlighted.

3.Press the cursor ◄► button until the language you want is selected.

4.Press the MENU button to close the OSD.

– 14 –

Image 21

Contents Page Copyright DisclaimerTrademark Recognition Symbols Used Important Safety InformationGeneral Safety Information IN3118HD User’s ManualProjector Installation Notice Power SafetyPreface Symbol Explanations Cleaning the ProjectorAbout this Manual Replacing the LampON-SCREEN DISPLAY OSD MENU SETTINGS SETUP AND OPERATIONMAINTENANCE AND SECURITY TROUBLESHOOTINGSAFETY CERTIFICATIONS PROJECTOR DIMENSIONSPROJECTION DISTANCE VS. PROJECTION SIZE TIMING MODE TABLEPacking Checklist GETTING STARTEDDLP Projector - User’s Manual Views of Projector Parts Front-right ViewLABEL DESCRIPTIONTop view-On-screen Display OSD buttons and LEDs see LED Error Messages on pageError code see LED Error Messages on page LABEL Rear viewDESCRIPTION SEE PAGEBottom view Remote Control Parts Adjust overscan Inserting the Remote Control Batteries SETUP AND OPERATIONStarting and Shutting down the Projector Adjusting the Projector Level Adjusting the Zoom ring, Focus and Keystone 1. Press the Volume but- tons on the projector or the remote control Adjusting the Volume2. Use the Vol +/- buttons on the projector or the remote control The volume control appears on the displayON-SCREEN DISPLAY OSD MENU SETTINGS Navigating the OSDOSD Menu Controls Set the OSD language to your preference before continuing Setting the OSD Language2. Press the cursor button until Language is highlighted 3. Press the cursor button until the language you want is selectedSETUP Basic OSD Menu OverviewSETUP Advanced PICTURE BasicPICTUREBasic Menu PICTUREAdvanced Menu Press the ENTER/SELECT button to enter the HSG Adjustment sub menu HSG AdjustmentDISPLAY Menu Press to change values for settingsSee PC Detail Adjustment on page PC Detail Adjustment SETUPBasic Menu Source Menu SettingsPress the ENTER/SELECT button to enter the Menu Settings sub menu Press the ENTER/SELECT button to enter the Source sub menuLan Control Settings Network State DLP Projector - User’s Manual Preparing Email Alerts Select the alert conditions by checking the desired boxes SETUPAdvanced Menu Lamp AudioPress the ENTER/SELECT button to enter the Audio sub menu Press the ENTER/SELECT button to enter the Lamp sub menuClosed Caption HDMIPress the ENTER/SELECT button to enter the HDMI sub menu Press the ENTER/SELECT button to enter the Closed Caption sub menuPresentation Timer STATUS Menu Replacing the Projection Lamp MAINTENANCE AND SECURITYRemove the lamp com- partment cover Remove the single screw on the lamp compartment coverRemove the three screws from the lamp module Lift the module handle up6. Pull firmly on the module handle to remove the lamp module Cleaning the Lens Cleaning the CaseCleaning the Projector TROUBLESHOOTING Common Problems and SolutionsTips for Troubleshooting Image Problems LED Error MessagesProblem No image appears on the screen Problem The image is blurredRemote Control Problems Lamp ProblemsProblem The image is streaked Problem The image is flat with no contrastHaving the Projector Serviced Audio ProblemsProblem There is no sound Problem The sound is distortedHDMI Q & A Q. How do I run HDMI cables longer than 10 meters?Q. How can I tell if a cable is an HDMI certified cable? Specifications SPECIFICATIONSModel Display type Native Resolution Projection distance Safety certification Operation temperature Dimensions W x D x HProjection Distance vs. Projection Size Projection Distance and Size Table169 SCREEN PROJECTION DISTANCEH-S YNC Timing Mode TableV-S YNC HDMIH-S YNC Projector Dimensions REGULATORY COMPLIANCE Safety CertificationsFCC Warning Canada