InFocus manual IN3118HD User’s Manual, Important Safety Information, Symbols Used

Page 3

IN3118HD User’s Manual

IN3118HD User’s Manual

Important Safety Information

Important:

It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference.

Symbols Used

Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information.

Note:

Provides additional information on the topic at hand.

Important:

Provides additional information that should not be overlooked.

Caution:

Alerts you to situations that may damage the unit.

Warning:

Alerts you to situations that may damage the unit, create a hazardous environment, or cause per- sonal injury.

Throughout this manual, component parts and items in the On-Screen Display (OSD) menus are denoted in bold font as in this example: “Push the MENU button on the remote control to open the DISPLAY menu.”

General Safety Information

¾Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in the unit. For servicing, contact InFocus at www.infocus.com/support

¾Follow all warnings and cautions in this manual and on the unit case.

¾The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the lens when the lamp is on.

¾Do not place the unit on an unstable surface, cart, or stand.

¾Avoid using the system near water, in direct sunlight, or near a heating device.

¾Do not place heavy objects such as books or bags on the unit.

— ii —

Image 3

Contents Page Copyright DisclaimerTrademark Recognition IN3118HD User’s Manual Important Safety InformationSymbols Used General Safety InformationProjector Installation Notice Power SafetyPreface Replacing the Lamp Cleaning the ProjectorSymbol Explanations About this ManualTROUBLESHOOTING SETUP AND OPERATIONON-SCREEN DISPLAY OSD MENU SETTINGS MAINTENANCE AND SECURITYTIMING MODE TABLE PROJECTOR DIMENSIONSSAFETY CERTIFICATIONS PROJECTION DISTANCE VS. PROJECTION SIZEPacking Checklist GETTING STARTEDDLP Projector - User’s Manual DESCRIPTION Front-right ViewViews of Projector Parts LABELTop view-On-screen Display OSD buttons and LEDs see LED Error Messages on pageError code see LED Error Messages on page SEE PAGE Rear viewLABEL DESCRIPTIONBottom view Remote Control Parts Adjust overscan Inserting the Remote Control Batteries SETUP AND OPERATIONStarting and Shutting down the Projector Adjusting the Projector Level Adjusting the Zoom ring, Focus and Keystone The volume control appears on the display Adjusting the Volume1. Press the Volume but- tons on the projector or the remote control 2. Use the Vol +/- buttons on the projector or the remote controlON-SCREEN DISPLAY OSD MENU SETTINGS Navigating the OSDOSD Menu Controls 3. Press the cursor button until the language you want is selected Setting the OSD LanguageSet the OSD language to your preference before continuing 2. Press the cursor button until Language is highlightedPICTURE Basic OSD Menu OverviewSETUP Basic SETUP AdvancedPICTUREBasic Menu PICTUREAdvanced Menu Press the ENTER/SELECT button to enter the HSG Adjustment sub menu HSG AdjustmentDISPLAY Menu Press to change values for settingsSee PC Detail Adjustment on page PC Detail Adjustment SETUPBasic Menu Press the ENTER/SELECT button to enter the Source sub menu Menu SettingsSource Press the ENTER/SELECT button to enter the Menu Settings sub menuLan Control Settings Network State DLP Projector - User’s Manual Preparing Email Alerts Select the alert conditions by checking the desired boxes SETUPAdvanced Menu Press the ENTER/SELECT button to enter the Lamp sub menu AudioLamp Press the ENTER/SELECT button to enter the Audio sub menuPress the ENTER/SELECT button to enter the Closed Caption sub menu HDMIClosed Caption Press the ENTER/SELECT button to enter the HDMI sub menuPresentation Timer STATUS Menu Replacing the Projection Lamp MAINTENANCE AND SECURITYLift the module handle up Remove the single screw on the lamp compartment coverRemove the lamp com- partment cover Remove the three screws from the lamp module6. Pull firmly on the module handle to remove the lamp module Cleaning the Lens Cleaning the CaseCleaning the Projector TROUBLESHOOTING Common Problems and SolutionsTips for Troubleshooting Problem The image is blurred LED Error MessagesImage Problems Problem No image appears on the screenProblem The image is flat with no contrast Lamp ProblemsRemote Control Problems Problem The image is streakedProblem The sound is distorted Audio ProblemsHaving the Projector Serviced Problem There is no soundHDMI Q & A Q. How do I run HDMI cables longer than 10 meters?Q. How can I tell if a cable is an HDMI certified cable? Safety certification Operation temperature Dimensions W x D x H SPECIFICATIONSSpecifications Model Display type Native Resolution Projection distancePROJECTION DISTANCE Projection Distance and Size TableProjection Distance vs. Projection Size 169 SCREENHDMI Timing Mode TableH-S YNC V-S YNCHDMI Projector Dimensions Canada Safety CertificationsREGULATORY COMPLIANCE FCC Warning