InFocus IN3118HD manual Lamp Problems, Remote Control Problems, Problem The image is streaked

Page 46

Problem: The image is streaked

DLP Projector – User’s Manual

Problem: The image is streaked

1.Set the Frequency and Tracking settings on the Display >> PC Detail Adjustment menu of the OSD to the default settings.

2.To ensure the problem is not caused by a connected PC’s video card, connect to another computer.

Problem: The image is flat with no contrast

Adjust the Contrast setting on the Picture >> Basic menu of the OSD.

Problem: The color of the projected image does not match the source image.

Adjust the Color Temperature and Gamma settings on the Picture >> Advanced menu of the OSD.

Lamp Problems

Problem: There is no light from the projector

1.Check that the power cable is securely connected.

2.Ensure the power source is good by testing with another electrical device.

3.Restart the projector in the correct order and check that the Power LED is green.

4.If you have replaced the lamp recently, try resetting the lamp connections.

5.Replace the lamp module.

6.Put the old lamp back in the projector and have the projector serviced.

Problem: The lamp goes off

1.Power surges can cause the lamp to turn off. Unplug and re-plug the power cord and press the Power button.

2.If the lamp still does not ignite, unplug the projector and allow it to cool for 60 minutes. Replace the lamp.

3.If a new lamp does not resolve the issue, put the old lamp back into the projector and arrange to have the projector repaired.

Remote Control Problems

Problem: The projector does not respond to the remote control

1.Direct the remote control towards remote sensor on the projector.

2.Ensure the path between remote and sensor is not obstructed.

3.Turn off any fluorescent lights in the room.

4.Check the battery polarity.

5.Replace the batteries.

6.Turn off other Infrared-enabled devices in the vicinity.

7.Have the remote control replaced.

– 39 –

Image 46

Contents Page Disclaimer CopyrightTrademark Recognition General Safety Information Important Safety InformationSymbols Used IN3118HD User’s ManualPower Safety Projector Installation NoticePreface About this Manual Cleaning the ProjectorSymbol Explanations Replacing the LampMAINTENANCE AND SECURITY SETUP AND OPERATIONON-SCREEN DISPLAY OSD MENU SETTINGS TROUBLESHOOTINGPROJECTION DISTANCE VS. PROJECTION SIZE PROJECTOR DIMENSIONSSAFETY CERTIFICATIONS TIMING MODE TABLEGETTING STARTED Packing ChecklistDLP Projector - User’s Manual LABEL Front-right ViewViews of Projector Parts DESCRIPTIONsee LED Error Messages on page Top view-On-screen Display OSD buttons and LEDsError code see LED Error Messages on page DESCRIPTION Rear viewLABEL SEE PAGEBottom view Remote Control Parts Adjust overscan SETUP AND OPERATION Inserting the Remote Control BatteriesStarting and Shutting down the Projector Adjusting the Projector Level Adjusting the Zoom ring, Focus and Keystone 2. Use the Vol +/- buttons on the projector or the remote control Adjusting the Volume1. Press the Volume but- tons on the projector or the remote control The volume control appears on the displayNavigating the OSD ON-SCREEN DISPLAY OSD MENU SETTINGSOSD Menu Controls 2. Press the cursor button until Language is highlighted Setting the OSD LanguageSet the OSD language to your preference before continuing 3. Press the cursor button until the language you want is selectedSETUP Advanced OSD Menu OverviewSETUP Basic PICTURE BasicPICTUREBasic Menu PICTUREAdvanced Menu HSG Adjustment Press the ENTER/SELECT button to enter the HSG Adjustment sub menuPress to change values for settings DISPLAY MenuSee PC Detail Adjustment on page PC Detail Adjustment SETUPBasic Menu Press the ENTER/SELECT button to enter the Menu Settings sub menu Menu SettingsSource Press the ENTER/SELECT button to enter the Source sub menuLan Control Settings Network State DLP Projector - User’s Manual Preparing Email Alerts Select the alert conditions by checking the desired boxes SETUPAdvanced Menu Press the ENTER/SELECT button to enter the Audio sub menu AudioLamp Press the ENTER/SELECT button to enter the Lamp sub menuPress the ENTER/SELECT button to enter the HDMI sub menu HDMIClosed Caption Press the ENTER/SELECT button to enter the Closed Caption sub menuPresentation Timer STATUS Menu MAINTENANCE AND SECURITY Replacing the Projection LampRemove the three screws from the lamp module Remove the single screw on the lamp compartment coverRemove the lamp com- partment cover Lift the module handle up6. Pull firmly on the module handle to remove the lamp module Cleaning the Case Cleaning the LensCleaning the Projector Common Problems and Solutions TROUBLESHOOTINGTips for Troubleshooting Problem No image appears on the screen LED Error MessagesImage Problems Problem The image is blurredProblem The image is streaked Lamp ProblemsRemote Control Problems Problem The image is flat with no contrastProblem There is no sound Audio ProblemsHaving the Projector Serviced Problem The sound is distortedQ. How do I run HDMI cables longer than 10 meters? HDMI Q & AQ. How can I tell if a cable is an HDMI certified cable? Model Display type Native Resolution Projection distance SPECIFICATIONSSpecifications Safety certification Operation temperature Dimensions W x D x H169 SCREEN Projection Distance and Size TableProjection Distance vs. Projection Size PROJECTION DISTANCEV-S YNC Timing Mode TableH-S YNC HDMIV-S YNC Projector Dimensions FCC Warning Safety CertificationsREGULATORY COMPLIANCE Canada