JVC DT-V24L3DY, DT-V20L3DY Menu Configuration-MAIN Menu, Picture Function, Operation guide

Page 10

Menu Configuration—MAIN MENU

For the operation procedure, see page 7.

Operation guide

Shows the buttons for each operation.

•The menu automatically disappears in about 30 seconds after the previous operation.

•Some items may not appear on the menu depending on the input or the input signal.

•The items controlled by the MAKE system do not appear on the menu.

10

PICTURE FUNCTION

Setting for the picture quality

Item

 

To do

Setting value

MOVING

 

Reduce the lag of moving pictures which is peculiar to LCD.

OFF, ON

PICTURE*1

 

 

 

APERTURE

 

Select the frequency of the luminance signal compensated in

OFF, LOW, HIGH

FREQ.*2

 

“APERTURE LEVEL.”

 

APERTURE

 

Compensate the frequency response of the luminance signal of the

01 – 10

LEVEL*2

 

video signal.

 

CTI

 

Adjust the clearness of the outlines of the chrominance signal.

OFF, NORMAL, HARD

LTI

 

Adjust the clearness of the outlines of the luminance signal.

OFF, NORMAL, HARD

I/P MODE

 

Selects a proper mode corresponding to the input picture.

NORMAL, CINEMA,

 

 

 

FIELD

sub menu

 

Display the sub menu which enables you to adjust the items of “PICTURE FUNCTION” while

 

 

viewing the actual picture.

 

reset

 

Restore the default settings for all the items in “PICTURE FUNCTION.”

 

*1 DT-V24L3DY only

 

*2 Memorized for each input.

 

 

Setting value: –20 – +20

 

BACK LIGHT

 

Adjusts the brightness of the display.

DVI INPUT SEL. Setting value: AUTO, MODE1, MODE2, MODE3

When “AUTO” is selected, the format of signals come in to the DVI-D (HDCP) terminal is automatically recognized. (Normally, select “AUTO.”)

•Select “MODE1”, “MODE2” or “MODE3” when the picture is not displayed correctly with “AUTO.”

•DVI-D input of the monitor is compatible with HDCP.

COMPO./RGB SEL. Setting value: COMPO. (component), RGB

Selects the signal type you want to use for COMPO./RGB terminals.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents DT-V24L3DY Safety Precautions These openings must not be blocked or coveredImportant Safety Instructions To install the stand InstallationTo detach the stand To prevent an accidental fall To adjust the stand heightFix the monitor to a wall by using strings Higher position Lower positionFront panel Press buttons to select an item, then press button Press or button when a menu is not displayedDisplay the menu Press Menu buttonAttaching the power cord holder Rear panelComputer signals preset DVI-D Hdcp terminals Available signalsVideo signals Specification of the DVI-D Hdcp terminalPicture Function Menu Configuration-MAIN MenuSetting value -20 +20 Operation guideSettings for marker functions 1/2 Setting of Area MARKER, Safety MARKER, R-AREA MarkerMARKER*1*2 Settings of E.AUDIO Group Example of the wave form monitor Wave Form SETTING*1Sync Function Settings of sub menu Posi Settings of SD43 LargeControl Lock Setting value OFF, on Setting of Character SETSettings for the information display of the monitor InformationControl priority is as follows External ControlAbout the external control MAKE/TRIGGER systemOperation of the external control Using the MAKE/TRIGGER systemTo assign the functions to the pin terminals Functions controlled by the MAKE/TRIGGER systemCommand outline Using the serial communicationCommunication specifications Basic command listTroubleshooting Maintenance20 Self-check programGeneral SpecificationsInput/output terminals Front view Dimensions Unit mm inchSide view Page DT-V24L3DY/DT-V20L3DY Multi Format LCD Monitor
Top Page Image Contents