JVC DT-V20L3DY, DT-V24L3DY specifications Important Safety Instructions

Page 3

FCC NOTICE

CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

IMPORTANT RECYCLING INFORMATION

This product has a fluorescent lamp that contains mercury. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities or for USA, the Electronic Industries Alliance: http://www.eiae.org

WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTHING CONNECTION.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.

REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

IMPORTANT SAFETY INSTRUCTIONS

1)Read these instructions.

2)Keep these instructions.

3)Heed all warnings.

4)Follow all instructions.

5)Do not use this apparatus near water.

6)Clean only with dry cloth.

7)Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9)Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11)Only use attachments/accessories specified by the manufacturer.

12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13)Unplug this apparatus during lightning storms or when unused for long periods of time.

14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15)Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

16)Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

17)When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.

3

Image 3
Contents DT-V24L3DY These openings must not be blocked or covered Safety PrecautionsImportant Safety Instructions Installation To install the standTo detach the stand Higher position Lower position To adjust the stand heightFix the monitor to a wall by using strings To prevent an accidental fallFront panel Press Menu button Press or button when a menu is not displayedDisplay the menu Press buttons to select an item, then press buttonRear panel Attaching the power cord holderSpecification of the DVI-D Hdcp terminal Available signalsVideo signals Computer signals preset DVI-D Hdcp terminalsOperation guide Menu Configuration-MAIN MenuSetting value -20 +20 Picture FunctionSetting of Area MARKER, Safety MARKER, R-AREA Marker Settings for marker functions 1/2MARKER*1*2 Settings of E.AUDIO Group Wave Form SETTING*1 Example of the wave form monitorSync Function Settings of SD43 Large Settings of sub menu PosiInformation Setting of Character SETSettings for the information display of the monitor Control Lock Setting value OFF, onMAKE/TRIGGER system External ControlAbout the external control Control priority is as followsFunctions controlled by the MAKE/TRIGGER system Using the MAKE/TRIGGER systemTo assign the functions to the pin terminals Operation of the external controlBasic command list Using the serial communicationCommunication specifications Command outlineTroubleshooting Self-check program Maintenance20Specifications GeneralInput/output terminals Dimensions Unit mm inch Front viewSide view Page DT-V24L3DY/DT-V20L3DY Multi Format LCD Monitor