JVC DT-V20L3DY Using the MAKE/TRIGGER system, To assign the functions to the pin terminals

7Using the MAKE/TRIGGER system

The MAKE/TRIGGER terminal is configured as follows. You can assign a function to each pin terminal in “REMOTE SETTING” (☞ “PIN1, PIN2, PIN3, PIN4, PIN5” on page 15).

• You cannot change the functions assigned to the pin terminals from 6th to 8th.

	Pin No.	Pin name
	1	PIN1
	2	PIN2
	3	PIN3
This is a female terminal.	4	PIN4
	5	PIN5
	6	PIN6 (TALLY)*1
	7	PIN7 (ENABLE)*2
	8	PIN8 (GND)

*1 The 6th pin terminal controls turning on or off the tally lamp (available to control even when the 7th pin terminal is invalid).

*2 The 7th pin terminal makes the external control valid/invalid. Make sure to control the terminal by the MAKE system.

To assign the functions to the pin terminals

For the operation procedure, see page 7.

1Select “REMOTE SETTING” on the SET-UP MENU.

2Set “PARALLEL TYPE” to “SET.”

3Select a pin name (“PIN1” – “PIN5”) for which you want to assign a function, then select the function you want to assign.

• For selectable functions, see the tables on the right.

Operation of the external control

1Set “PARALLEL TYPE” of “REMOTE SETTING” to “MAKE” or “TRIGGER” in the SET-UP MENU.

2Short-circuit the 7th pin terminal (ENABLE) to the 8th pin terminal (GND) so that the monitor can be controlled by the external control.

3When the “MAKE” system is selected: Operate each function by short-circuiting the corresponding pin terminal to the 8th pin terminal (GND) or opening it.

When the “TRIGGER” system is selected: Operate each function by pulse control, that is short-circuiting the corresponding pin terminal to the 8th pin terminal (GND) for about 1 second and opening it.

•When changing the input with MAKE system, only one pin terminal must be short-circuited. (Other pin terminals must be opened.)

•When selecting the “TRIGGER” system, you can operate only one function at a time. Operate the functions one by one.

<Functions controlled by the MAKE/TRIGGER system>

Display	Functions to be controlled	Opening		Short-circuiting
TALLY SEL	Selects the color of the tally lamp.	Green		Red
SDI 1	Changes the input to “SDI 1.”	Invalid		Valid
SDI 2	Changes the input to “SDI 2.”	Invalid		Valid
DVI	Changes the input to “DVI.”	Invalid		Valid
COMP./RGB	Changes the input to “COMPO./RGB.”	Invalid		Valid
VIDEO 1	Changes the input to “VIDEO 1.”	Invalid		Valid
VIDEO 2	Changes the input to “VIDEO 2.”	Invalid		Valid
EXT.SYNC	Changes the sync signal.	Internal sync		External sync
A.MARKER	The area marker indication	Off		On
S.MARKER	The safety marker indication	Off		On
FRAME	Indication of the area of the specified aspect ratio	Off		On
C.MARKER	The center marker indication	Off		On
MARK.SEL	Selects the items of “MARKER”*3	Non-“R-” items		“R-” items
ASPECT	Changes the aspect ratio.	4:3		16:9
1:1	Displays in 1:1 mode.	Off		On
STATUS	Status display*4	☞ “On the Status Display” on page 7
L.METER	Audio level meter display		*5
TIME CODE	Time code display	Off		On
SOURCE ID	☞ “SOURCE ID” on page 15	Off		On
WAVE FORM	Wave form monitor display	Off		On*6
C.C.	Closed caption display		*7
COLOR OFF	Color off	Color		Monochrome
SCR CHECK	Screens check		*8
I/P MODE	Change a mode according to a input picture.		*9
MUTING	Muting on/off	Off		On
– – –	No function	—		—

*3 Selects which functions in “MARKER” are activated, non-“R-” items or “R-” items (☞ “MARKER” on page 11).

*4 Displays the information shown when INPUT SELECT button of the current input is pressed (☞ “On the Status Display” on page 7). While controlling with the MAKE system, the information is displayed only at the moment of short-circuiting.

*5 While controlling with the MAKE system, the level meter is switched between displayed (short-circuiting) and hidden (opening). When “LEVEL METER ch” is set to “OFF,” the level meter is not displayed (“NO EFFECT” appears). While controlling with the TRIGGER system, the pattern of the audio channel display is switched.

*6 While controlling with the MAKE system, the wave form monitor will not disappear until opening the terminal (regardless of the “AUTO OFF” setting on page 13).

*7 For analog composite signals (NTSC and B/W60 only). While controlling with the MAKE system, the closed caption is switched between displayed (short-circuiting) and hidden (opening). When “CLOSED CAPTION” is set to “OFF,” the closed caption is not displayed (“NO EFFECT” appears). While controlling with the TRIGGER system, the type of the closed caption can be selected.

*8 While controlling with the MAKE system, the screen is switched between normal screen (opening) and blue screen (short-circuiting). While controlling with the TRIGGER system, the screen changes as same as when pressing SCREENS CHECK button (☞ page 6).

*9 Must be controlled with the TRIGGER system. The mode changes in the order of “NORMAL” \ “CINEMA” \ “FIELD”. (This function cannot be controlled with the MAKE system.)

•You cannot assign the same function to different pin terminals.

•The TRIGGER system switches each function by short-circuiting the pin terminal for about 1 second and opening it.

17