JVC DT-V24L3DY External Control, About the external control, Control priority is as follows

Page 16

External Control

7About the external control

This monitor has three external control terminals.

•MAKE/TRIGGER terminal (RJ-45): The following external control systems are available.

(1)MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to the GND pin terminal, or disconnecting (opening) it.

(2)TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the corresponding pin terminal.

☞ “Using the MAKE/TRIGGER system” on page 17

•RS-485 terminals (RJ-45): Controls the monitor with the RS-485 system. (☞ “Using the serial communication” on page 18)

•RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-232C system. (☞ “Using the serial communication” on page 18)

Set the following items of “REMOTE SETTING” in SET-UP MENU according to the external control terminal and control system (☞ “SERIAL TYPE”, “PARALLEL TYPE” on page 15).

Control terminal

Control system

 

The settings of this unit

 

“SERIAL TYPE” setting

“PARALLEL TYPE” setting

 

 

 

MAKE/TRIGGER

MAKE

 

—

MAKE

terminal

 

 

 

 

TRIGGER

 

—

TRIGGER

 

 

RS-485 terminal

Serial

RS-485

RS485*1

—

RS-232C terminal

communication

RS-232C

RS232C*1

—

*1 For a monitor connected to a personal computer etc, select the terminal the equipment is actually connected to. For other monitors, select “RS485.”

16

Control priority is as follows.

MAKE > TRIGGER = serial communication = buttons and menu on the monitor

•You can use the external control even when “CONTROL LOCK” is set to “ON” (☞ page 15).

•When the monitor is off (on standby), external control is not available. But certain external controls (starting/ terminating communication, turning on the monitor) are available through the serial communication (☞ page 18).

<MAKE/TRIGGER system>

You can control the monitor by a personal computer or dedicated controller*2.

• For the details, see page 17.

*2 The controller is not commercially available. Consult your dealer if you need it.

<Serial communication>

PC, etc.

RS-485 IN

RS-485 RS-485

RS-485

RS-485

RS-485

or

OUT

IN

OUT

IN

OUT

RS-232C

 

 

 

 

 

• For the details, see page 18.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents DT-V24L3DY Safety Precautions These openings must not be blocked or coveredImportant Safety Instructions To install the stand InstallationTo detach the stand To adjust the stand height Fix the monitor to a wall by using stringsTo prevent an accidental fall Higher position Lower positionFront panel Press or button when a menu is not displayed Display the menuPress buttons to select an item, then press button Press Menu buttonAttaching the power cord holder Rear panelAvailable signals Video signalsComputer signals preset DVI-D Hdcp terminals Specification of the DVI-D Hdcp terminalMenu Configuration-MAIN Menu Setting value -20 +20Picture Function Operation guideSettings for marker functions 1/2 Setting of Area MARKER, Safety MARKER, R-AREA MarkerMARKER*1*2 Settings of E.AUDIO Group Example of the wave form monitor Wave Form SETTING*1Sync Function Settings of sub menu Posi Settings of SD43 LargeSetting of Character SET Settings for the information display of the monitorControl Lock Setting value OFF, on InformationExternal Control About the external controlControl priority is as follows MAKE/TRIGGER systemUsing the MAKE/TRIGGER system To assign the functions to the pin terminalsOperation of the external control Functions controlled by the MAKE/TRIGGER systemUsing the serial communication Communication specificationsCommand outline Basic command listTroubleshooting Maintenance20 Self-check programGeneral SpecificationsInput/output terminals Front view Dimensions Unit mm inchSide view Page DT-V24L3DY/DT-V20L3DY Multi Format LCD Monitor
Top Page Image Contents