Onkyo HT-RC260 Error Messages, Changing the Speaker Settings Manually, Using a Powered Subwoofer

Page 24

7 Use qw/ to select an option, and then press

ENTER.

2EQ: Auto Setup

 

- - Review Speaker Configuration - -

 

Subwoofer

Yes

 

Front

Full Band

TV

Center

40Hz

 

Surround

100Hz

 

Front Wide

None

 

Front High

100Hz

 

Surr Back

120Hz

 

Surr Back Ch

2ch

 

Save

 

 

Cancel

 

 

The options are:

`Save:

Save the calculated settings and exit Audyssey 2EQ® Room Correction and Speaker Setup.

`Cancel:

Cancel Audyssey 2EQ Room Correction and

Speaker Setup.

Note

You can view the calculated settings for the speaker con- figuration, speaker distances, and speaker levels by using e/r.

8 Disconnect the speaker setup microphone.

Note

When Audyssey 2EQ Room Correction and Speaker Setup is complete, the “Equalizer” will be set to “Audyssey” (37). The Audyssey indicator will light (8).

You can cancel Audyssey 2EQ Room Correction and Speaker Setup at any point in this procedure simply by disconnecting the setup microphone.

Do not connect or disconnect any speakers during Audyssey 2EQ Room Correction and Speaker Setup.

If the AV receiver is muted, it will be unmuted automatically when Audyssey 2EQ Room Correction and Speaker Setup starts.

Changes to the room after Audyssey 2EQ Room Correction and Speaker Setup requires you run Audyssey 2EQ Room Correc- tion and Speaker Setup again, as room EQ characteristics may have changed.

Error Messages

While Audyssey 2EQ Room Correction and Speaker Setup is in progress, one of the error messages below may appear.

2EQ: Auto Setup

Ambient noise is too high.

Retry

Cancel

Error message

The options are:

`Retry:

Try again.

`Cancel:

Cancel Audyssey 2EQ Room Correction and Speaker Setup.

• Ambient noise is too high.

The background noise is too loud. Remove the source of the noise and try again.

• Speaker Matching Error!

The number of speakers detected was different from that of the first measurement. Check the speaker con- nection.

• Writing Error!

This message appears if saving fails. Try saving again. If this message appears after 2 or 3 attempts, contact your Onkyo dealer.

• Speaker Detect Error

This message appears if a speaker is not detected. “No” means that no speaker was detected.

Tip

• See “Speaker Configuration” for appropriate settings (11).

Changing the Speaker Settings Manually

You can manually make changes to the settings found dur- ing Audyssey 2EQ Room Correction and Speaker Setup. See also:

“Speaker Configuration” (36)

“Speaker Distance” (37)

“Level Calibration” (37)

“Equalizer Settings” (37)

Using a Powered Subwoofer

If you’re using a powered subwoofer and it outputs very low-frequency sound at a low volume level, it may not be detected by Audyssey 2EQ Room Correction and Speaker Setup.

If the “Subwoofer” appears on the “Review Speaker Configuration” screen as “No”, increase the subwoofer’s volume to the half-way point, set it to its highest crossover frequency, and then try running Audyssey 2EQ Room Correction and Speaker Setup again. Note that if the vol- ume is set too high and the sound distorts, detection issues may occur, so use an appropriate volume level. If the sub- woofer has a low-pass filter switch, set it to Off or Direct. Refer to your subwoofer’s instruction manual for details.

En

24

Image 24
Contents HT-RC260 Always consider the environmental issues and follow 10 cm 4 at the rear. The rear edge of the shelf orBoard above the apparatus shall be set 10 cm Away from the rear panel or wall, creating a flue-likePrecautions Supplied Accessories Using the Remote ControllerInstalling the Batteries Aiming the Remote ControllerContents Features AmplifierProcessing MiscellaneousHdmi Thru indicator TUNING, Preset 25 to 26, arrowFront & Rear Panels Front PanelUREMOTE Control jack DisplayRear Panel CENTER, FRONT, SURR, Surr Back or Front High or Front WideRemote Controller Controlling the AV ReceiverReturn button Controlling the tunerAbout Home Theater Enjoying Home TheaterConnecting the AV Receiver Connecting Your SpeakersSpeaker Configuration Speaker Connection PrecautionsConnecting the Speaker Cables Speaker cables, and twist the bare wires tightly, as shownScrew-type speaker terminals Strip 1/2 to 5/8 12 to 15 mm Connecting a Powered Subwoofer Bi-amping the Front SpeakersAbout AV Connections Connected image with AV componentsAV Cables and Jacks Hdmi cableConnecting Components with Hdmi Jack Signal Components AssignableAudio return channel ARC function Connecting External Components How to record the videoFront RearConnecting Onkyo uComponents Connecting AntennaSystem On/Auto Power On Remote ControlSignal Selection Which Connections Should I Use?Video Connection Formats Audio Connection FormatsTurning On/Off the AV Receiver Turning OnTurning Off Selecting the Language Used for the Onscreen Setup Menus Setting the Display BrightnessBasic Operations Playing the Connected ComponentUsing the Sleep Timer Using the Audio and Video MenusMuting the AV Receiver Selecting Speaker LayoutUsing Headphones Audyssey 2EQ Room Correction and Speaker SetupChanging the Input Display Measurement time varies depending on the number of speakersUsing Audyssey 2EQ EnterError Messages Changing the Speaker Settings ManuallyUsing a Powered Subwoofer Using the Tuner Tuning into Radio StationsListening to the Radio Listening to the RadioPresetting FM/AM Stations Selecting PresetsDeleting Presets ModeRecording AV RecordingThat you want to record On your recorder, start recordingUsing the Listening Modes Listening Mode ButtonsSelecting Listening Modes MOVIE/TV button Game buttonAbout Listening Modes Explanatory NotesInput Source Speaker LayoutListening Modes Resolution Audio Dolby Digital Plus *5Dolby TrueHD DTS-HD HighOnkyo-Original DSP Listening Modes UnpluggedAdvanced Setup On-screen Setup MenusCommon Procedures in Setup Menu MenuInput/Output Assign Monitor OutHdmi Input BD/DVD, VCR/DVR, CBL/SAT, GAME, TV/CD PortSpeaker Setup Speaker SettingsComponent Video Input Digital Audio InputSpeaker Terminal Assign Front High/Front Wide/Zone2 SurrBack/Front High/Front WideFront Center*1, Surround*1, Surr Back*2*3*4*5Audio Adjust Equalizer SettingsSpeaker Distance Level CalibrationDolby Audyssey DSXSource Setup Theater-DimensionalAudyssey IntelliVolume SyncName Edit Picture Adjust Game ModeTo correct a character Wide Mode*1*2Picture Mode*1*2 Film Mode*2Edge Enhancement*2 Noise Reduction*2Listening Mode Preset Volume SetupOSD Setup MiscellaneousHardware Setup Remote IDTuner Lock Setup Using the Audio SettingsTone Control Settings Audyssey Settings Speaker LevelsLate Night Music OptimizerAdjusting the Bass & Treble Setting the Incoming Digital Signal Fixed ModeBass Treble Connecting Zone Connecting Your Zone 2 Speakers Directly to the AV receiverConnecting Your Zone 2 Speakers to an Amp in Zone ZoneSetting the Powered Zone Using Zone Controlling Zone 2 from the AV receiverControlling Zone 2 with the Remote Controller Adjusting the Volume for ZoneOperating with the remote controller Muting ZoneConnecting an Onkyo Dock Controlling iPodModels sold are different depending on the region Onkyo Dock CableUsing the Onkyo Dock UP-A1 DockControlling Your iPod RI DockWithout the RI Control With the RI ControlAvailable buttons Preprogrammed Remote Control Codes Looking up for Remote Control CodeControlling Other Components Entering Remote Control Codes Remote Control Codes for Onkyo Components Connected via uRemote Mode BD/DVD TV/CDResetting Remote Mode Buttons Resetting the Remote ControllerYou can reset the remote controller to its default settings Controlling Other ComponentsSetup Components ButtonsCassettetape deck ON/STANDBY Input TV VOL q / w GuideTroubleshooting Standby indicator flashes redCan’t turn on the AV receiver There’s no sound, or it’s very quietThere’s no sound with a certain signal format About DTS signalsOnly the front speakers produce sound Only the center speaker produces soundRemote controller doesn’t work There’s no picture from a source connected to an HdmiOn-screen menus don’t appear On screen display does not appearAV receiver’s remote controller doesn’t control your iPod Sound changes when I connect my headphonesCan’t record Zone 2 speakers produce no soundImportant Note Regarding Video Playback Nent Video OUTSpecifications Amplifier Section GeneralVideo Section Tuner SectionAbout Hdmi Supported Audio FormatsAbout Copyright Protection Using an RIHD-compatible TV, Player, or Recorder About p-compatible componentsOperations that can be performed with p connection How to connect and setup Confirm the connecting and settingChange each item in the Hdmi Setup as below Confirm the settingsVideo Resolution Chart OutputInput Output 1080p 1080i 720p 480p 480iMemo Memo Memo Onkyo Europe Electronics GmbH Onkyo Europe Electronics GmbH UK Branch

HT-RC260 specifications

The Onkyo HT-RC260 is a versatile and powerful home theater receiver designed to enhance your audio-visual experience. While it may not be the latest model on the market, its combination of features and technologies makes it an excellent choice for those looking to create a rich and immersive entertainment environment.

One of the standout features of the HT-RC260 is its robust amplification system. This receiver provides 7.2 channels of surround sound, delivering up to 100 watts per channel. This level of power ensures that your home theater can fill a room with dynamic sound, making every movie, music track, or game come to life. The receiver also supports various surround sound formats, including Dolby TrueHD and DTS-HD Master Audio, allowing for a cinematic experience at home.

Connectivity options abound with the HT-RC260. It includes multiple HDMI inputs, accommodating various devices such as Blu-ray players, game consoles, and streaming devices. The HDMI ports support 3D video and 4K passthrough, ensuring compatibility with the latest video technologies. Additionally, the receiver features analog and digital audio inputs, allowing you to connect legacy devices with ease.

The Onkyo HT-RC260 also integrates advanced calibration technology known as AccuEQ. This feature automatically measures the characteristics of your room and adjusts the audio output for optimal sound quality. As a result, users can enjoy consistent audio experiences regardless of room size or shape.

For those who value convenience, the HT-RC260 supports network streaming services. Users can access popular platforms like Spotify, Pandora, and TuneIn via built-in Wi-Fi. Additionally, the receiver can connect to home networks via Ethernet, expanding your listening options and making it easy to enjoy your favorite music.

The user interface is straightforward, with an intuitive on-screen display that simplifies setup and operation. The included remote control allows easy access to all functions, making it user-friendly even for those who may not be tech-savvy.

In summary, the Onkyo HT-RC260 is an excellent choice for home theater enthusiasts. With its powerful amplification, diverse connectivity, advanced audio calibration, and network streaming capabilities, it offers a well-rounded solution for anyone seeking to elevate their audiovisual experience. Whether you are watching films, playing video games, or listening to music, the HT-RC260 provides an engaging and harmonious soundstage that will enhance your enjoyment for years to come.