Onkyo HT-RC260 Speaker Terminal Assign Front High/Front Wide/Zone2, Surr Back Ch, Double Bass

■Speaker Terminal Assign Front High/Front Wide/Zone2

With this setting, you can specify the speakers con- nected to FRONT HIGH OR FRONT WIDE OR ZONE 2 SPEAKERS terminals.

`Front High:

Front high speakers can be used.

`Front Wide:

Front wide speakers can be used.

`Zone2:

Zone 2 speakers can be used (Powered Zone 2 enabled).

Note

•If the “Speakers Type” setting is set to “Bi-Amp”, Powered Zone 2 cannot be used.

•If “Front Wide” is selected in the “SurrBack/Front High/ Front Wide” setting, you cannot select “Front Wide” here.

SurrBack/Front High/Front Wide

With this setting, you can specify the speakers con-

nected to SURR BACK OR FRONT HIGH OR FRONT WIDE SPEAKERS terminals.

`Surr Back:

Surround back speakers can be used.

`Front High:

Front high speakers can be used.

`Front Wide:

Front wide speakers can be used.

Note

•If the “Speakers Type” setting is set to “Bi-Amp”, Powered Zone 2 cannot be used.

•If “Front High” is selected in the “Front High/Front Wide/ Zone2” setting, you cannot select “Front High” here.

Speaker Configuration

With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify “Full Band” for speakers that can output low fre- quency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover fre- quency will be output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequencies.

■Subwoofer

`Yes:

Select if a subwoofer is connected.

`No:

Select if no subwoofer is connected.

■Front

`Full Band

`40Hz to 80Hz to 100Hz, 120Hz, 150Hz, 200Hz

Note

•If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “Full Band”.

En

■Center*1, Surround*1, Surr Back*2*3*4*5

`Full Band

`40Hz to 80Hz to 100Hz, 120Hz, 150Hz, 200Hz

`None:

Select if no speaker is connected.

■Front Wide*1*2*4*6, Front High*1*2*4*7

`Full Band

`40Hz to 80Hz to 100Hz, 120Hz, 150Hz, 200Hz

`None:

Select if no speaker is connected.

Note

*1 “Full Band” can be selected only when “Full Band” is selected in the “Front” setting.

*2 If the “Surround” setting is set to “None”, this setting cannot be selected.

*3 If the “Surround” setting is set to anything other than “Full Band”, “Full Band” cannot be selected here.

*4 If the “Speakers Type” setting is set to “Bi-Amp” (➔ 35), or Powered Zone 2 is being used (➔ 49), this setting cannot be selected.

*5 If you have selected other than “Surr Back” in the “Surr- Back/Front High/Front Wide” setting, this setting cannot be selected.

*6 If you have selected other than “Front Wide” in the “Front High/Front Wide/Zone2” or “SurrBack/Front High/Front Wide” setting, this setting cannot be selected.

*7 If you have selected other than “Front High” in the “Front High/Front Wide/Zone2” or “SurrBack/Front High/Front Wide” setting, this setting cannot be selected.

■Surr Back Ch

`1ch:

Select if only one surround back speaker L is con- nected.

`2ch:

Select if two (left and right) surround back speakers are connected.

Note

•If the “Surr Back” setting is set to “None” (➔ 48), this setting cannot be selected.

■LPF of LFE

(Low-Pass Filter for the LFE Channel)

`80Hz, 90Hz, 100Hz, 120Hz

With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

■Double Bass

This setting is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup function (➔ 22).

With the Double Bass function, you can boost bass out- put by feeding bass sounds from the front left, right, and center channels to the subwoofer.

`On:

Double Bass function on.

`Off:

Double Bass function off.

36