Sharp PGB10S operation manual Regarding the Lamp, Replacing the Lamp

Page 69
U.S.A. ONLY

Regarding the Lamp

Lamp

■It is recommended that the lamp (sold separately) be replaced when the remaining lamp life be- comes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. See page 41.

■For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho-

rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Caution Concerning the Lamp

■This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

■Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to remove the damaged lamp and assure safe operation.

Replacing the Lamp

Caution

•Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching it can lead to burn or injury.

•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

■If the new lamp does not light after replacement, take your projector to the nearest Sharp Autho- rized Projector Dealer or Service Center for repair. Purchase a replacement lamp unit of type BQC- PGB10S//1 from your nearest Sharp Authorized Projector Dealer or Service Center. Then carefully change the lamp by following the instructions described in this section. If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.

Appendix

-65

Page 68 Page 70
Image 69
Page 68 Page 70
Contents PG-B10S Model No. PG-B10S Serial No Special Note for Users in the U.K Page Introduction Product Disposal When Attaching the Quick Guide LabelFor Future Reference Contents Screen Setup Important Safeguards Info For other operating systems For other languages To install Acrobat Reader from the CD-ROMAccessories Supplied accessoriesOptional accessories Projector Front and Top View Part NamesPower indicator About the Indicators on the ProjectorLamp indicator Temperature warning indicatorProjector Rear View Using the Kensington LockRS-232C terminal Input 1 terminal INPUT/OUTPUT Terminals and Connectable Main EquipmentFORWARD/BACK buttons Remote Control Front ViewWhen using the remote control Using the Remote ControlUsable Range Inserting the BatteriesSetup and Projection Adjust the projected image Press on the projector or on the remote control Plug the power cord into the wall outletPower indicator On button Lamp indicator Image ProjectionSwitching the Input Mode Adjusting the VolumePress or on the remote con- trol to adjust the volume Correcting Trapezoidal Distortion Press To enter the Key Stone Correction modeAV Mute button Keystone buttonPress , , \ and to adjust the Keystone Correction Turning the Power off PuttingProjector into the Standby Mode PressZoom knob Focus ring Adjusting the LensPress Height Adjust button Using the Adjustment FeetHeight Adjust button foot Rear adjustment foot ButtonVariable Lens Shift Feature When moving upward or downwardLens shift lever Adjusting the Projected Image Position Switching the Resize Mode Resize ModeUndo button Resize buttonVideo Freeze and Enlarge Image Press to cancel the operationLocking the Operation Buttons Taking the Keylock off Keylock FunctionWhen using the Input 1 mode When using the Input 2 or Input 3 modeMenu Items Menuthe Adjustments Using the Menu ScreenMenu Selections Press \or to display the other menu screensPress \ or to adjust the item selected Press or to select the item you want to adjustSettings Sub menu Adjusting the Image Picture AdjustmentSelect the item on the Picture menu and adjust the image CLR Temp Adjusting Color TemperatureSRGB sRGB Setting Select Gamma on the Picture menu and the desired gamma modeExample Picture screen menu for Input 1 RGB mode Gamma Gamma CorrectionMemory Storing and Selecting the Adjustment Settings Signal Type Signal Type SettingAdjusting the Computer Image Special Modes Special Computer Image AdjustmentMode Settings Example Fine Sync menu screen for Input 1 modeSignal Info Checking the Input Signal Auto Sync Auto Sync Adjust- mentLamp Timer Life Check Using the Options MenuOSD Display Setting On- screen Display Ing the Lamp Life StatusExample Options menu screen for Input 2 S-Video mode Video System SettingVideo System Background Selecting a Startup and Background ImageEco Mode Setting the Eco Mode Auto Power Off AutoPower Off Function Select on or OFF in Auto Power Off on the Options menuMenu Position Selecting Menu Screen PositionMenu Color Selecting the Menu Color Password Setting a Password If You Forget Your PasswordPress , and to enter the password Anti-TheftSetting the Anti-TheftSelect Anti-Theft on the Op Tions menu, then press Keycode input box Press on the remote control Using the Language MenuSelecting the On-screen Display Language Press \ or to select the Lan- guage menu iconPress \ or to select the PRJ Mode menu icon Using the PRJ Mode MenuReversing the Projected Image Press or to select Rear, Then pressConnecting the Projector to Other Devices Before ConnectingThis projector can be connected to Connecting to a Computer Using the RGB Cable Connecting the Projector to a ComputerConnecting to Video Equipment Cable Connecting to Component Video EquipmentControlling the Projector Using a Computer Connecting the Power Watching Images on Both the Projector and a MonitorCord Standard Setup Front Projection Setting up the ScreenScreen Size and Projection Distance Normal ModeProjection from behind the Screen Projecting a Reversed ImageHow to Use Carrying Case Carrying the ProjectorLens cap Lens shipping block Cleaning the projector MaintenanceCleaning the lens Cleaning the exhaust and intake ventsPut the projector into the standby mode Cleaning and Replacing the Air FilterDisconnect the power cord Replacing the Air FilterTab User service screw Clean the air filterRemove the air filter Replace the air filterMaintenance Indicators About the lamp indicatorAbout the temperature warning indicator Maintenance Indicators Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Change the air filterRemove the lamp unit cover Resetting the Lamp Timer DIN-D-sub RS-232C adaptor 9-pinD-sub male connector Connecting Pin AssignmentsCommands RS-232C Specifications and Command SettingsPC control Communication conditionsComputer Computer Compatibility Chart51-55 TroubleshootingTroubleshooting For Sharp Assistance NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM SpecificationsUnits inches mm DimensionsAnti-Theft GlossaryBorder IndexSharp Corporation
Top Page Image Contents