Sharp PGB10S operation manual Removing and Installing the Lamp Unit, Change the air filter

Page 70

Regarding the Lamp

Removing and Installing the Lamp Unit

Info

•Be sure to remove the lamp unit using the handle. Be sure not to touch the glass sur- face of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

•Please refer to the installation manual in- cluded with the lamp unit.

1Press on the projector or STANDBY on the remote control to

put the projector into the standby mode.

•Wait until the cooling fan stops.

Warning!

•Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury.

2Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3Change the air filter.

•Change the air filter whenever you in- stall the lamp unit (see pages 61 and 62).

4Remove the lamp unit cover.

•Turn the projector over. Loosen the user service screw (1) that secures the lamp

unit cover. Pressing the tab, remove the lamp unit cover (2).

Lamp

unit	BQC-PGB10S//1

STANDBY button

STANDBY

STANDBY button

AC socket

User
service screw	1
Tab	2
Tab

-66

Image 70

Contents PG-B10S Model No. PG-B10S Serial No Special Note for Users in the U.K Page Introduction When Attaching the Quick Guide Label Product DisposalFor Future Reference Contents Screen Setup Important Safeguards Info To install Acrobat Reader from the CD-ROM For other operating systems For other languagesSupplied accessories AccessoriesOptional accessories Part Names Projector Front and Top ViewLamp indicator About the Indicators on the ProjectorPower indicator Temperature warning indicatorUsing the Kensington Lock Projector Rear ViewINPUT/OUTPUT Terminals and Connectable Main Equipment RS-232C terminal Input 1 terminalRemote Control Front View FORWARD/BACK buttonsUsable Range Using the Remote ControlWhen using the remote control Inserting the BatteriesSetup and Projection Adjust the projected image Power indicator On button Lamp indicator Plug the power cord into the wall outletPress on the projector or on the remote control Image ProjectionAdjusting the Volume Switching the Input ModePress or on the remote con- trol to adjust the volume AV Mute button Press To enter the Key Stone Correction modeCorrecting Trapezoidal Distortion Keystone buttonProjector into the Standby Mode Turning the Power off PuttingPress , , \ and to adjust the Keystone Correction PressAdjusting the Lens Zoom knob Focus ringHeight Adjust button foot Rear adjustment foot Using the Adjustment FeetPress Height Adjust button ButtonWhen moving upward or downward Variable Lens Shift FeatureLens shift lever Adjusting the Projected Image Position Undo button Resize ModeSwitching the Resize Mode Resize buttonVideo Press to cancel the operation Freeze and Enlarge ImageKeylock Function Locking the Operation Buttons Taking the Keylock offWhen using the Input 2 or Input 3 mode When using the Input 1 modeMenu Items Menuthe Menu Selections Using the Menu ScreenAdjustments Press \or to display the other menu screensPress or to select the item you want to adjust Press \ or to adjust the item selectedSettings Sub menu Select the item on the Picture menu and adjust the image Picture AdjustmentAdjusting the Image CLR Temp Adjusting Color TemperatureExample Picture screen menu for Input 1 RGB mode Select Gamma on the Picture menu and the desired gamma modeSRGB sRGB Setting Gamma Gamma CorrectionSignal Type Signal Type Setting Memory Storing and Selecting the Adjustment SettingsMode Settings Computer Image AdjustmentAdjusting the Computer Image Special Modes Special Example Fine Sync menu screen for Input 1 modeAuto Sync Auto Sync Adjust- ment Signal Info Checking the Input SignalOSD Display Setting On- screen Display Using the Options MenuLamp Timer Life Check Ing the Lamp Life StatusVideo System Video System SettingExample Options menu screen for Input 2 S-Video mode Background Selecting a Startup and Background ImagePower Off Function Auto Power Off AutoEco Mode Setting the Eco Mode Select on or OFF in Auto Power Off on the Options menuMenu Screen Position Menu Position SelectingMenu Color Selecting the Menu Color If You Forget Your Password Password Setting a PasswordAnti-TheftSetting the Anti-Theft Press , and to enter the passwordSelect Anti-Theft on the Op Tions menu, then press Keycode input box Selecting the On-screen Display Language Using the Language MenuPress on the remote control Press \ or to select the Lan- guage menu iconReversing the Projected Image Using the PRJ Mode MenuPress \ or to select the PRJ Mode menu icon Press or to select Rear, Then pressBefore Connecting Connecting the Projector to Other DevicesThis projector can be connected to Connecting the Projector to a Computer Connecting to a Computer Using the RGB CableConnecting to Video Equipment Connecting to Component Video Equipment CableControlling the Projector Using a Computer Watching Images on Both the Projector and a Monitor Connecting the PowerCord Setting up the Screen Standard Setup Front ProjectionNormal Mode Screen Size and Projection DistanceProjecting a Reversed Image Projection from behind the ScreenCarrying the Projector How to Use Carrying CaseLens cap Lens shipping block Cleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsDisconnect the power cord Cleaning and Replacing the Air FilterPut the projector into the standby mode Replacing the Air FilterRemove the air filter Clean the air filterTab User service screw Replace the air filterAbout the lamp indicator Maintenance IndicatorsAbout the temperature warning indicator Maintenance Indicators Lamp Regarding the LampReplacing the Lamp Change the air filter Removing and Installing the Lamp UnitRemove the lamp unit cover Resetting the Lamp Timer Connecting Pin Assignments DIN-D-sub RS-232C adaptor 9-pinD-sub male connectorPC control RS-232C Specifications and Command SettingsCommands Communication conditionsComputer Compatibility Chart ComputerTroubleshooting 51-55Troubleshooting For Sharp Assistance Specifications NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAMDimensions Units inches mmGlossary Anti-TheftIndex BorderSharp Corporation