Sharp JW-21MN manual Waterproof and insulation processing of connectors, Branch connector, Remarks

Page 25

7-4 Waterproof and insulation processing of connectors

In order to prevent water intrusion into the "T" branch connectors and the straight connectors, we recommend to wind a self-adhesive tape and provide waterproof processing for them. For insulation purposes, cover these connectors with jackets.

(1)"T" branch connector

To wind a self-adhesive tape, cut the tape at about 10 cm each and start winding from position . Start winding cut tapes from and as well.

Self-adhesive tape

7

TÕs

(2)Straight connector

To wind the self-adhesive tape, cut the tape at about 15 cm each and start winding from position .

Self-adhesive tape

Straight

Remarks

Prior to adhering the tape, clean the surface of the connectors and stick the adhesive side of the tape on the connector surface. Wind to lightly spread on the connector surface, and overlap with the next wrap to half of the tape width. Wind the tape for each wrap evenly so that the connector metal portion is completely covered with the tape.

Be careful not to excessively stretch the tape.

7-4

Image 25

Contents JW-21MN JW-21MN Installation Safety PrecautionsWiring Compel Use Maintenance ProhibitME-NET Module JW-21MN Table of contents Errors and Countermeasures 12-1 to Setting of Switches and Parameter 11-1 toDescription for Computer Link Operation 10-1 to 13-1 Support Tools 14-1 to Specifications 15-1 toAppendix 16-1 to Data link function Features and FunctionsComputer link function Wiring InstallationConnector Treatment MaintenanceStatic electricity Allocation of relay numberJW20H JW-21MN JW-21MN JW30H System ConfigurationFront view Name and Function of Each PartInstallation procedure InstallationRemarks Name Model Maker Processing of CablesProcessing cable end Cutting of coating, external conductor, and insulator Fine adjustment of blade cutting depthRemoval of coating, external conductor, and insulator Processing of cable end Display of blade settingConnector ME-GP-01 Processing procedure Insert a sleeve Connector crimping procedureRequired tools Hand-held crimping tool Crimping contactInsulation test Fixing the connectorConductivity test Cable trunk and branch lines Wiring Method Relaying of trunk cables Cable wiring procedure in control panel Page Branch connector Waterproof and insulation processing of connectorsStraight connector RemarksCheck after wiring Wiring of cables at outside control panelsStation number of the additional station Branching methodReason Memory address for data links Memory Address on the ME-NETMemory address map against JW20/JW20H JW30H address ME-NET address Memory address map against JW30HJW20/20H ME-NET address Capacity Memory addresses for computer linksJW30H address ME-NET address Capacity Remarks Communication method Description for Data Link OperationData link Standard function Relay linkData link Save memory function Setting item Set locationRegister link Required transmission time Required transmission time and communication delay timeCommunication delay time An example of synchronized transfer by OUT instruction Data transmission between master PC and slave PCExpansion of network Multiple installation of the JW-21MNCase of mounting 4 sets of JW-21MN Hierarchical link Optional commands Basic commandsDescription for Computer Link Operation Computer link function10-2 Basic commands10-3 Optional commandsCommunication format, basic pattern Read free memory size Write mode assignment None Communication formatMonitor TMR, CNT, and MD 10-4Setting PC mode Reading PC mode10-5 Writing system memory Reading system memory10-6 Write mode assignment 1 or Communication format Setting dateReading date 10-7Reading time Setting time10-8 Monitor step status JW20/JW20H only Correct clock time10-9 Read the optional parameters Write mode assignmentSet the optional parameters 10-10Set the special I/O parameters Read the special I/O parameters10-11 Set the secret function JW30H only Release the secret function, register password JW30H only10-12 10-13 Check the secret function JW30H only10-14 Response on errorOperation procedure Setting of Switches and Parameter11-1 Mode switch Mode Switch setting of master station and slave stationModule No. switch Unit no 11-2Termination resistance switch LT Station number switch STA no11-3 Reference Need for the termination resistance11-4 Shield ground switch LGSetting contents of master station parameters Value H 11-6Parameter for setting in slave station Parameter for setting in master stationCommunication area map 11-711-8 11-9 + ｈ11-10 Example for settingMaser station Slave station Standard Save memory 11-11 When master station PC is JW20/JW20H11-12 When master station PC is JW30H11-13 Setting procedureExample Stop operation of data link HEX hexadecimal, byte 11-14Stop operation of data link HEX hexadecimal, byte Set number of connecting stations DCM decimal, byte Data link function setting HEX hexadecimal, byte11-15 Set top address of register link area on the master station 11-16Set in parameter addresses 005000 to 11-1711-18 Set connection status of slave station Bit pattern, byte 11-1911-20 PC operation 11-21Contents Setting item11-22 When PC is JW20/JW20H Setting range of flag areaWhen PC is JW30H 11-2311-24 11-25 Turn on the power of slave station PC Connect support tools11-26 11-27 11-28 Indication lamps Errors and Countermeasures12-1 Details MeasureRemark Flag12-3 Case of a master stationCommunication monitor flag Operation condition monitor flag12-4 Case of slave station 01 to12-5 Monitor operation condition by each station PC12-6 Storage of error codeSystem memory #160 to 167 self diagnosis error code System memory #170 to 177 option module error codeSystem memory #150 monitor error switch number 12-712-8 Error history13-1 Replacement of the JW-21MNRecord and load by ladder software JW-92SP, JW-50SP Record Support Tools14-1 14-2 LoadLoad to the personal computer Stop operation of the JW-21MNGeneral specifications SpecificationsCommunication specifications SpecificationStandard function Specifications Data link specificationsSave memory function Specifications 15-2Outside dimensional drawings Computer link specifications15-3 Appendix Maintenance and check16-1 Check flow chart Recovery method at communication errors16-2 16-3 Check cable/connectorCause Countermeasure 16-4007764 to 16-5Check items of cables and connectors Switches required check in the JW-21MN16-6 Other casesIdentify the error station Check the errors timingWhen identification of the cause is difficult 16-716-8 Table of parameter memoryMaster station 16-9 Set contents Setting method value, example16-10 16-11 Slave station 01 to 16-1216-13 Special functions unique to the JW-21MNRemote programming and remote monitor Support tool Opposite module Connection moduleFunction Standard network connection 16-14Expansion network connection Operation example16-15 Network settingWhen used with a computer link Parameter setting by remote function16-16 Alphabetical Index Operation procedure Waterproof and insulation processing of connectors