Runco VX-5000d, VX-4000d manual Service, Input Names Restore Composite Video Component SD

Page 63

Operation

Use the Service menu to access advanced projector configuration settings. This menu should be used by ISF-certified technicians only.

You must enter a passcode to access the Service menu.

Note

Test Video: Select Test Video from the Service Menu to access the internal test patterns on the VX-4000d/VX-5000d. Four patterns are available, consisting of white/gray or colored bars.

Press MENU to exit test pattern mode.

Service

Service

Test Video

Input Names

Remote Control

Analog Out Mode

Display Device

HD Format

Triggers

Miscellaneous

Resolution

System Reset

Restore Saved Settings

Input Names: You can give each DHD Controller input a descriptive name. For example, you may want to change the default input name to the type of source component connected to it: “VCR,” “DVD,” “Laptop” et cetera. Composite, S-Video and Component SD input names can be up to 12 characters long; the others can be up to eight characters long.

To edit an input name, select Input Names from the Service menu. Press or to select an input and press ENTER. Use the or buttons to change a character; press or to select a character to change. When you have finished editing the input name, press MENU.

To restore the default input name, press repeatedly to highlight that input name in the “Restore” column. Then, press ENTER.

To save input names so that they can be restored after a System Reset (described on page 54), press repeatedly to highlight “Save.” Then, press ENTER.

The button takes you from top to bottom in the left column, then

Note from top to bottom in the right column. To highlight “Save,” scroll through both columns.

Remote Control: The Remote Control menu shows you the primary and secondary infrared (IR) codes to which the VX-4000d/VX-5000d will respond. By default, both are set to 17. You can change these codes if either:

•Another device in the theater (a DVD player, for example) is responding to commands from the standard DHD remote control (Figure 2-6)in ways that are unpredictable or undesirable.

•You have multiple VX-4000d/VX-5000d projectors and want to control them independently, as opposed to broadcasting commands from a single remote to all of them. In this scenario, you can use multiple remotes programmed to use different IR codes. Or, you can use a single remote and change the IR code as needed to address a specific projector.

Input Names

 

Restore

Composite

Composite

 

 

S-Video 1

S-Video 1

S-Video 2

S-Video 2

Component SD

Component SD

HD/RGB 1

HD/RGB 1

HD/RGB 2

HD/RGB 2

DVI 1

DVI 1

DVI 2

DVI 2

Save

 

Runco VX-4000d/VX-5000d Owner’s Operating Manual

51

Page 62 Page 64
Image 63
Page 62 Page 64
Contents VX-4000d VX-5000d Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents List of Figures List of Figures Xii About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories VX-4000d/VX-5000d at a Glance Controls and FunctionsVX-5000d Front/Top/Side/Bottom View Vertical Lens Shift VX-4000d/VX-5000d Rear Panel ComLink Input DB-9 male connectorDHD Controller Front Panel DHD Controller Front PanelDown Button DHD Controller Rear Panel OutputsInputs 10. IR Video 1 / S-VIDEOVolt 750 mA Trigger Outputs ComLink RS-232 OutputStandard DHD Remote Control VX-4000d/VX-5000d Remote Control UnitsComp Component On / OFFCursor Buttons Video4X3 Standard 43 Memory Preset Buttons ISF NT NightAspect Ratio Selection Buttons ANA AnamorphicVolume +/- / Mute / OK / CH + Touch-Screen Remote ControlDVI 1 / DVI CompVID 1 / S-VID HD 1 / HDEnter / Cursor Buttons Focus / Focus +Zoom / Zoom + Operation InstallationOther surfaces Quick Setup Installation OverviewStep Procedure For Details, Refer to Considerations InstallationProjector Installation Options Installation TypeLens Option Note Throw Dist VX-4000d Lens Options and Throw RatiosThrow Distance Throw Ratio Throw Distance RangeProteus F with CineWide VX-5000d Lens Options and Throw RatiosLens Option Note Minimum Maximum Proteus FVertical and Horizontal PositionLens Shift Horizontal Lens Shift Folded Optics Other Considerations Installing the Optional CineWide LensMounting VX-4000d/VX-5000dConnections to the VX-4000d/VX-5000d and DHD Controller Connecting the VX-4000d/VX-5000d to the DHD Controller Connecting Source Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See Figure10. Analog RGB Connections Analog Computer RGB Connections See Figure11. Composite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See FigureConnection RS-232 ControllerConnecting to AC Power Installation Selecting the Input Source Turning on the PowerAdjusting the Picture Orientation OperationLens Adjustments FocusZoom Using the On-Screen Menus Aspect Ratio ISF PresetsService Input SourceHD Pass Thru 1 HD Pass Thru Main MenuInput Source Aspect RatioAspect Ratio Description Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input PositionSerial Num Hardware Firmware 0002.001A Date Feb 9 ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default InformationCalibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above Input Names Restore Composite Video Component SD ServiceKeystone Correction Vertical Keystone CorrectionADC Bandwidth Auto YPbPr Input Resolution HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVAuto Operation Lamp Replacement Maintenance and TroubleshootingVX-5000d Lens Assembly Exploded View Lens ReplacementMaintenance and Troubleshooting Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Display Device on Maintenance and Troubleshooting Serial Communications RS-232 Connection and Port ConfigurationSerial Command Syntax Serial CommandsAspect Ratio Commands Image Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Status Command Parameter Value Description Min/maxSpecifications VX-4000d/VX-5000d SpecificationsVX-4000d/VX-5000d Specifications Dimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsDHD Controller Specifications DHD Controller SpecificationsVX-4000d/VX-5000d Dimensions VX-4000d/VX-5000d DimensionsPage Runco CL-810 Owner’s Operating Manual
Top Page Image Contents