Runco VX-5000d, VX-4000d manual Maintenance and Troubleshooting, Lamp Replacement

Page 67

5. Maintenance and Troubleshooting

The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or sooner if a noticeable degradation in brightness occurs. Contact your Runco dealer to obtain a replacement lamp.

1.Turn off the projector and unplug the power cord. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement.

2.Using a flat-blade screwdriver, loosen the two captive Lamp Cover screws on the side of the projector and remove the cover.

5.1

Lamp Replacement

REMOVE

THESE SCREWS

3.Remove the three Phillips round-head lamp assembly mounting screws. These are identified by arrows pointing to them on the lamp housing.

4.Grasp the lamp assembly handle and pull gently, removing the lamp module from the projector housing.

5.Install the new lamp module. Secure it in place with the three screws that you removed in Step 3.

6.Replace the lamp cover and re-tighten the two Lamp Cover screws.

7.Turn the projector on.

8.Reset the Lamp Hour counter. To do this, select Service from the Main Menu, then Display Device, then Installation. Use the cursor buttons to highlight Reset under “Lamp Hours” and press ENTER.

Runco VX-4000d/VX-5000d Owner’s Operating Manual

55

Image 67

Contents VX-4000d VX-5000d Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents List of Figures List of Figures Xii About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories VX-4000d/VX-5000d at a Glance Controls and FunctionsVX-5000d Front/Top/Side/Bottom View Vertical Lens Shift VX-4000d/VX-5000d Rear Panel ComLink Input DB-9 male connectorDHD Controller Front Panel DHD Controller Front PanelDown Button Outputs DHD Controller Rear PanelInputs 10. IR Video 1 / S-VIDEOVolt 750 mA Trigger Outputs ComLink RS-232 OutputStandard DHD Remote Control VX-4000d/VX-5000d Remote Control UnitsComp Component On / OFFCursor Buttons Video4X3 Standard 43 Memory Preset Buttons ISF NT NightAspect Ratio Selection Buttons ANA AnamorphicVolume +/- / Mute / OK / CH + Touch-Screen Remote ControlDVI 1 / DVI CompVID 1 / S-VID HD 1 / HDFocus / Focus + Enter / Cursor ButtonsZoom / Zoom + Operation InstallationOther surfaces Installation Overview Quick SetupStep Procedure For Details, Refer to Considerations InstallationProjector Installation Options Installation TypeLens Option Note Throw Dist VX-4000d Lens Options and Throw RatiosThrow Distance Throw Ratio Throw Distance RangeProteus F with CineWide VX-5000d Lens Options and Throw RatiosLens Option Note Minimum Maximum Proteus FPosition Vertical and HorizontalLens Shift Horizontal Lens Shift Folded Optics Other Considerations Installing the Optional CineWide LensVX-4000d/VX-5000d MountingConnections to the VX-4000d/VX-5000d and DHD Controller Connecting the VX-4000d/VX-5000d to the DHD Controller Connecting Source Digital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See Figure10. Analog RGB Connections Analog Computer RGB Connections See Figure11. Composite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See FigureConnection RS-232 ControllerConnecting to AC Power Installation Selecting the Input Source Turning on the PowerAdjusting the Picture Orientation OperationFocus Lens AdjustmentsZoom Using the On-Screen Menus Aspect Ratio ISF PresetsService Input SourceHD Pass Thru 1 HD Pass Thru Main MenuInput Source Aspect RatioAspect Ratio Description Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input PositionSerial Num Hardware Firmware 0002.001A Date Feb 9 ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default InformationCalibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above Input Names Restore Composite Video Component SD ServiceKeystone Correction Vertical Keystone CorrectionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV ADC Bandwidth Auto YPbPr Input ResolutionAuto Operation Lamp Replacement Maintenance and TroubleshootingVX-5000d Lens Assembly Exploded View Lens ReplacementMaintenance and Troubleshooting Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Display Device on Maintenance and Troubleshooting Serial Communications RS-232 Connection and Port ConfigurationSerial Command Syntax Serial CommandsAspect Ratio Commands Image Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Status Command Parameter Value Description Min/maxVX-4000d/VX-5000d Specifications SpecificationsVX-4000d/VX-5000d Specifications Dimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsDHD Controller Specifications DHD Controller SpecificationsVX-4000d/VX-5000d Dimensions VX-4000d/VX-5000d DimensionsPage Runco CL-810 Owner’s Operating Manual