Runco CL-510 Ansi Lumen specification, Csms Home Theater Calibration Ansi Lumen Specification

Page 33

Runco CL-510/ CL-510LT User’s Manual

*ANSI Lumen specification:

This is the typical projector luminosity (brightness) specification found in most sales literature. This measurement is included in RUNCO literature to allow for direct comparison with other manufacturer's projectors. These measurements can be taken at 9,000 to 13,000 degree Kelvin to get expected performance data when the projector is used in professional, commercial, and industrial displays.

**CSMS Home Theater Calibration ANSI Lumen Specification:

These measurements are taken from the projector as setup in a home theater environment. The projector is calibrated to ISF specifications including setting the color temperature to 6500 degree Kelvin, the standard for reproducing video.

**CSMS Home Theater Calibration foot-Lambert (fL) Specification:

This is the unit of measurement used in commercial movie theaters to express image brightness. The Society of Motion Picture and Television Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using an open gate (without film in the projector). More importantly, today SMPTE specifies 12 fL as the target image brightness in Digital Cinema theaters using DLP™ technology. The foot-Lambert is dependant on screen size, screen gain, and projector light output.

All measurements are made at RUNCO to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter and Minolta LS-100 Light Meter, Video Essentials test DVD, and a Stewart Filmscreen StudioTech

130, 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6500 o Kelvin and has a minimum of 150 hours of usage.

306. Additional Information

Page 32 Page 34
Image 33
Page 32 Page 34
Contents CL-510 / CL-510LT What is not Covered Under the Terms of this Warranty What is Covered Under the Terms of this WarrantyEffective Warranty Date RIGHTS, Limits and ExclusionsImportant Warranty Registration To Obtain SERVICE, Contact Your Runco DealerAdditional Information Runco CL-510/ CL-510LT Video Projector User’s Manual Table of Contents Overview FeaturesProjector Exterior View Front / Upper SideRear / Bottom Side Control Panel Controls and FunctionsLamp LED Zoom RingDVI/ Hdcp Connector PanelOFF Remote ControlPIP+ ActivePIP RGB HDRemote Control InstallationConnect the Power Cord ProjectorAdjust the height Adjust the Lens Zoom/Focus ringScreen H x W Installation For CL-510 With 1.75 2.00 LensThrow Distance Vertical OffsetScreen Hight Screen Width Min TD Max TD Vertical Offset Throw Distance Chart For CL-510 With 1.75 2.00 LensInstallation For CL-510LT With 2.30 3.00 Lens Throw Distance Chart For CL-510LT With 2.30 3.00 Lens Connecting Connecting Video InputsVideo / S-Video / Component Interlaced Video Rgbhv DTV RGB Progressive Component DTV Y/PB/PRConnecting a Computer DVI/ Hdcp Zoom/ Focusing Turning on the PowerBasic Operation Selecting Video MemoryDirect Picture Adjust Menu Bypass Setting MenuSelecting Aspect Ratio PIP/ PBP function Selecting Input SourceTurning off the Power Using the Menu MenuMain Menu Picture Quality Adjustments Aspect RatioScreens Options Setup White Balance To adjust grey scale Replace the Lamp Contact your Runco Dealer Additional InformationProblem Possible Cause Remedy TroubleshootingCL-510/ CL-510LT Specifications SpecificationsAnsi Lumen specification Csms Home Theater Calibration Ansi Lumen SpecificationCsms Home Theater Calibration foot-Lambert fL Specification Dimensions RS-232C Control Codes PC Out Adapter RS-232 SetupRUMA-010300 rev
Top Page Image Contents