AMX NXR-ZGW/-ZRP manual Table top installation of the NXR-ZGW and NXR-ZRP

Page 17

Installation

Using the PSN NetLinx connector for power

The PWR and GND cable from the 12 VDC power supply must be connected to the corresponding location on the 2-pin 3.5 mm mini-captive wire connector (FIG. 6).

PWR +

GND -

To the Device

FIG. 6 12 VDC Power Connector Wiring Diagram

12 VDC Power Supply

1.Insert the PWR and GND wires on the terminal end of a PSN 2-pin 3.5 mm mini-captive wire cable. Match the wiring locations of the +/- on both the power supply and the terminal connector.

2.Tighten the clamp to secure the two wires. Do not over-torque the screws; doing so may strip the threads and damage the connector.

3.Verify the connection of the 2-pin 3.5 mm mini-captive wire to the power supply.

Table top installation of the NXR-ZGW and NXR-ZRP

Using the provided rubber pads, place one in each bottom corner of the device.

Rack mounting the NXR-ZGW and NXR-ZRP

Using the Velcro pad provided, remove the backing and adhere one side to the device. Remove the backing of the other side of the Velcro and place it on your rack where you want the NXR-ZGW/ZRP mounted.

Before continuing, consult Setting up a Network section on page 13.

NXR-ZGW/-ZRP	11

Image 17

Contents NXR-ZGW/-ZRP AMX Limited Warranty and Disclaimer Software License and Warranty Agreement Page Table of Contents Device Configuration Overview NXR-ZGW SpecificationsNXR-ZGW FG5791-01 Specifications NXA-WAP 2403A 3 dBI Antenna FG2255-20 NXR-ZRP FG5791-02 Specifications NXR-ZRP SpecificationsFront and Rear Components of the NXR-ZRP Network structure How ZigBee worksMesh Network Arrangements Single PAN ID installationsMultiple PAN ID installations Multiple PAN ID Network FCC ComplianceNXR-ZGW/-ZRP Location and Antenna Direction InstallationThings to Consider Before Starting Connecting Power to the NXR-ZGW and NXR-ZRP Connecting the NXR-ZGW to a LANConnecting the Optional Accessory Antennas Determining the Power SourceRack mounting the NXR-ZGW and NXR-ZRP Table top installation of the NXR-ZGW and NXR-ZRPUsing the PSN NetLinx connector for power NXR-ZGW/-ZRP Setting up a Network NXR-ZGW/-ZRP Summary NXR-ZGW Browser-based Configuration Manager PagesSummary of Gateway Settings Determining the PAN settings of the NXR-ZGW Determining the IP settings of the NXR-ZGWRebooting the Configuration Manager Checking the firmware versionNetwork IP Settings ConfigurationSetting the IP Address IP AddressUser Settings Setting the DNS AddressSetting a new username and password User SettingsConnecting an NXR-ZRP to the network for the first time Enabling and disabling the wireless networkPersonal Area Network PAN NetworkConnecting a Repeater to the Gateway Setting the PAN channelFinding a device’s EUI address ConnectionsFinding the device’s description Determining the device typeChecking the device link status Determining the device link qualityPAN Device Details PAN Device DetailsRemoving a device from the Access List Putting a device on the Access ListLocating the device Changing a Connected Device descriptionChanging a device’s ZigBee networking information Allowing firmware updates to all devices on a network Allowing firmware updates to individual devicesUtilities Device FirmwareDetermining the connection status of a device Connection LogFinding the device’s Icsp number Connection LogTraffic Log Traffic LogFinding the device traffic NXR-ZGW/-ZRP Before beginning the Upgrade process Device ConfigurationSending Firmware to The NXR-ZGW Upgrading The NXR-ZGW via An IP AddressVerifying and Upgrading the device firmware via an IP Assigning Communication Settings and TCP/IP SettingsSelect the device’s firmware file from the Files section FIG Using the ID Button to Change the NXR-ZGW’s Device Number NXR-ZGW/-ZRP It’s Your World Take Control