AMX NXB-KNX manual SET Telnet Port, SET Time, Show LOG ALL

Page 24

Programming - Telnet Commands

Terminal Commands (Cont.)

Command

Description

 

 

 

 

SET TELNET PORT

Sets the NXB-KNX’s IP port listened to for Telnet connections.

 

Note: The NXB-KNX must be rebooted to enable new settings.

 

Example:

 

 

 

>SET TELNET PORT

 

 

Current telnet port number = 23

 

Enter new telnet port number (Usually 23)(0=disable Telnet):

 

Once you enter a value and press the ENTER key, you get the follow-

 

ing message:

 

 

 

Setting telnet port number to 23

 

New telnet port number set, reboot the NXB-KNX for the

 

change to take affect.

 

 

 

 

SET TIME

Sets the current time.

 

 

Example:

 

 

 

>SET TIME

 

 

 

Enter Date: (hh:mm:ss) ->

 

Note: Due to the absence of a battery-backed real-time clock, setting

 

the current time is only valid for the life of the current run. When the

 

unit is rebooted, the time will be lost.

 

 

SHOW LOG

Displays the log of messages stored in the NXB-KNX's memory.

 

The NXB-KNX logs all internal messages and keeps the most recent

 

messages. The log contains:·

 

 

• Entries starting with first specified or most recent

 

• Date, Day, and Time message was logged

 

• Which object originated the message

 

• The text of the message:

 

 

SHOW LOG [start] [end]

 

 

SHOW LOG ALL

 

 

- <start> specifies message to begin the display.

 

- If start is not entered, the most recent message will be first.

 

- If end is not entered, the last 20 messages will be shown.

 

- If <ALL> is entered, all stored messages will be shown, starting

 

with the most recent.

 

 

Example:

 

 

 

>SHOW LOG

 

 

 

Message Log for System 50 Version: v2.10.75

 

Entry

Date/Time

Object

 

Text

 

 

 

-----------------------------------------------------------------

1:11-01-2001 THU 14:14:49 ConnectionManager Memory Available = 11436804 <26572>

2:11-01-2001 THU 14:12:14 ConnectionManager Memory Available = 11463376 <65544>

3:11-01-2001 THU 14:10:21 ConnectionManager Memory Available = 11528920 <11512>

4:11-01-2001 THU 14:10:21 TelnetSvr

Accepted Telnet connection:socket=14 addr=192.168.16.110 port=2979

5:11-01-2001 THU 14:05:51 Interpreter CIpEvent::OnLine 10002:1:50

6:11-01-2001 THU 14:05:51 Interpreter CIpEvent::OnLine 128:1:50

7:11-01-2001 THU 14:05:51 Interpreter CIpEvent::OffLine 128:1:50

8:11-01-2001 THU 14:05:51 Interpreter CIpEvent::OnLine 96:1:50

9:11-01-2001 THU 14:05:51 Interpreter CIpEvent::OffLine 96:1:50

10:11-01-2001 THU 14:05:51 Interpreter CIpEvent::OnLine 128:1:50

11:11-01-2001 THU 14:05:51 Interpreter CIpEvent::OnLine 96:1:50

12:11-01-2001 THU 14:05:51 Interpreter CIpEvent::OnLine 5001:16:50

13:11-01-2001 THU 14:05:51 Interpreter CIpEvent::OnLine 5001:15:50

14:11-01-2001 THU 14:05:51 Interpreter

20

NXB-KNX NetLinx KNX Interface

Image 24
Contents NXB-KNX AMX Limited Warranty and Disclaimer Table of Contents Table of Contents NXB-KNX NetLinx KNX Interface Product Specifications OverviewIntended for indoor use only Installation Wiring and ConnectionsEthernet 10/100 Base-T RJ-45 Wiring Configuration KNX Connector PoE Power Over EthernetConfiguration Bonjour Zero-Configuration ClientOverview Determining the IP Address of the NXB-KNXAdmin Menu Accessing the WebConsoleSecurity Settings Enable / Disable Security SettingsLogin Information IP Settings Logging Into the Configuration Manager With Security EnabledPort Settings Port SettingsClock Manager Mode Manager Clock ManagerClock Manager Daylight Savings Clock Manager Daylight Savings ManagerClock Manager Nist Servers Only one Nist server is selectable at any given timeApplication Upgrade Current Application InformationBrowse for new Application Upload File Firmware Upgrade Current Firmware InformationBrowse for new Firmware Upload File Programming Telnet Commands Establishing a Terminal Connection Via TelnetTerminal Commands Reboot Security SetupMEM MSG OnoffSET Ethernet Mode CMD SET DNSSET Java Heap SET FTP PortSET Https Port SET IPSET LOG Count SET SSH PortSET Telnet Port SET TimeShow LOG Show LOG ALLShow Heap Show MEMTime Programming Telnet Commands NXB-KNX NetLinx KNX Interface Programming Telnet Commands NXB-KNX NetLinx KNX Interface It’s Your World Take Control