American Power Conversion AP9615 manual Ways, as shown in Figure

Page 8

Product Description continued

Station ports The Station ports are the first 4 RJ-45ports, which are labeled 1X – 4X. The Station ports use straight-through UTP cables to connect the hub with:

•Workstations or other non-hub devices that you want to include in your network.

•The Uplink port of another hub in a cascading config- uration.

Note: A Station port acts as an Uplink port when it is used

 

 

 

with a crossover cable.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Uplink port

The Uplink port is normally used in either of the following

 

ways, as shown in Figure 2.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

➊

 

 

 

 

 

 

To

➋

 

 

 

 

 

 

 

 

 

 

Corporate LAN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1X

2X 3X 4X Uplink

 

 

 

 

 

1X 2X 3X 4X Uplink

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

straight-through cable

crossover cable

Figure 2: Dual Use of the Uplink Port

™Connected in cascade with a Station port of another hub or switching device, using a straight-through cable.

šConnected to a workstation or other non-hub device, using a crossover cable.

Communication

The hub requires a category 3, 4, or 5 UTP 10Base-T com-

cables

munication cable for each device to be attached.

4

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Port 10Base-T Hub Thank You Contents Page SmartSlot 5-Port 10Base-T Hub is an APC accessory LAN by installing it in the SmartSlot of an APC UPS orIntroduction That allows you to expand or create a local area networkProduct Description For a description of the conditions indicated by LEDs Label Color Activity DescriptionWays, as shown in Figure Munication cable for each device to be attachedInstalling the Hub Shut down and power off the connected Turn off the System Enable switch onTurn off the ON/OFF switch on the front If present, unplug the Triple Chassis’s powerUse a #2 Phillips head screwdriver to remove Screws fastening the SmartSlot cover plate toBack panel of the UPS or triple chassis. Keep Screws for below. Save the SmartSlot coverUsing straight-through UTP cables, connect the Sta Procedure listed belowPlug the UPS back into the AC power outlet Press and hold the Power On button until youInstallation Procedure 2 central hubs As many as 32 stations, as shown below in . NoteUse of a crossover cable to connect the Uplink ports Removing the Hub Action Cause Solution TroubleshootingProvides suggestions for troubleshooting your hub Troubleshooting Suggestions Specifications Port 10Base-T HubWarranty Information Procedure Be prepared to provide a description of the problemTechnician will help solve the problem over Authorization RMA numberApplication of Council Directives Standards to WhichConformity is DeclaredW. a p c c . c o m
Top Page Image Contents