Linksys SRW208L, SRW208MP, SRW208G, SRW208P manual Rack-Mount Placement

Page 12

Chapter 3

Installation

Rack-Mount Placement

When rack-mounting the Switch, please observe the following guidelines:

•• Elevated Operating Ambient  If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

•• Reduced Air Flow  Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

•• Mechanical Loading  Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

•• Circuit Overloading  Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

•• Reliable Earthing  Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

To rack-mount the Switch in any standard 19-inch rack, follow the instructions described below.

1.Place the Switch on a hard flat surface with the front panel facing you.

2.Attach a rack–mount bracket to one side of the Switch with the supplied screws.Then attach the other bracket to the other side.

WARNING: Make sure you use the screws supplied with the mounting brackets. Using the wrong screws could damage the Switch and would invalidate your warranty.

Attaching the Brackets

8-Port 10/100 Ethernet Switch with Webview

3.Make sure the brackets are properly attached to the Switch.

4.Use the appropriate screws (not included) to securely attach the brackets to your rack.

Mounting in Rack

6

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Port 10/100 Ethernet Switch with Webview About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Port 10/100 Ethernet Switch with Webview Iii Table of Contents Appendix B Introduction Appendix F Regulatory InformationAppendix G Contact Information Chapter Introduction IntroductionWelcome Chapter Product Overview Product OverviewSRW208 Front Panel SRW208G Front PanelSRW208L Front Panel SRW208P/SRW208MP Front PanelBack Panel Chapter Installation InstallationPositioning the Switch Placement OptionsRack-Mount Placement Wall-Mount Placement Hardware Installation Chapter Configuration Using Console Interface Connecting to the Switch through a Telnet SessionSwitch Main Menu System Configuration MenuManagement Settings SSH Configuration User & Password Settings IP Configuration Https Configuration Port Configuration Port StatusHelp Chapter Advanced Configuration Advanced ConfigurationAccessing the Web-based Utility Setup SummarySetup Network Settings IP ConfigurationSystem Information PoE InformationSetup Time Port Management Port SettingsPort Configuration Detail Port Management Link Aggregation Link Aggregation DetailPort Management PoE Power Settings Port Management LacpVlan Management Port Settings Vlan Management Create VlanSingle Vlan Vlan RangeVlan Management Ports to Vlan Vlan Management Vlan to PortsVlan Management Gvrp Statistics Rmon StatisticsJoin Vlan Detail Statistics Rmon History Log TableStatistics Rmon Alarms Rmon HistoryStatistics Rmon Events Add EventStatistics Port Utilization Statistics 802.1x StatisticsStatistics Gvrp Statistics ACL IP based ACLACL MAC based ACL Security ACL Binding Security RadiusSecurity TACACS+ Security 802.1x Settings Setting TimerSecurity Ports Security Security Multiple Hosts QoS CoS Settings Security Storm ControlQoS QoS Queue Settings QoS Dscp SettingsCoS Default QoS BandwidthQoS Basic Mode QoS Advanced ModeOut of Profile Dscp Policy NameNew Class Map Spanning Tree Spanning Tree STP StatusNew Aggregate Policer Global Setting Bridge SettingsSpanning Tree Global STP Spanning Tree STP Port Settings Spanning Tree Rstp Port SettingsSpanning Tree Mstp Properties Established by the deviceSpanning Tree Mstp Instance Settings Multicast Igmp Snooping Multicast Bridge Multicast Snmp Global ParametersSnmp Views Snmp Group Profile Snmp Group MembershipSnmp Communities Base TableSnmp Notification Filter Snmp Notification RecipientAdvanced Table Admin User Authentication Admin Static AddressAdmin Dynamic Address Admin LoggingQuery Admin Port Mirroring Admin Cable TestAdmin Save Configuration Admin Firmware UpgradeBackup Via TftpAdmin Reboot Admin Factory DefaultsAdmin Server Logs Admin Memory Logs Admin Flash LogsAppendix a About Gigabit Ethernet Fiber Optic Cabling Gigabit EthernetFiber Optic Cabling Startup Menu Procedures Appendix B IntroductionDownloading Using Xmodem Appendix C Glossary GlossaryGlossary Smtp Simple Mail Transfer Protocol The standard e Appendix C Appendix D Specifications SpecificationsQoS Specifications SRW208L SRW208MP Limits Bandwidth Intensive Video Traffic to Only Requestors Support 256 multicast groups Ethernet Warranty Information Obtaining Warranty ServiceExclusions and Limitations Warranty Information Technical SupportSafety Notices Regulatory InformationFCC Statement Industry Canada StatementRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Appendix G Contact Information
Related manuals
Manual 3 pages 51.04 Kb Manual 142 pages 37.07 Kb Manual 3 pages 34.25 Kb
Top Page Image Contents