Linksys SRW208P, SRW208MP, SRW208L, SRW208G manual Hardware Installation

Page 14

Chapter 3

Installation

Hardware Installation

To connect network devices to the Switch, follow these instructions:

1.Make sure all the devices you will connect to the Switch are powered off.

2.For 10/100Mbps devices, connect a Category 5 Ethernet network cable to one of the numbered ports on the Switch. For a 1000Mbps device, connect a Category 5e Ethernet network cable to one of the numbered ports on the Switch.

3.Connect the other end to a PC or other network device.

4.Repeat steps 2 and 3 to connect additional devices.

5.If you are using the mini-GBIC port, then connect the mini-GBIC module to the mini-GBIC port. For detailed instructions, refer to the module’s documentation.

6.If you will use the Switch’s console interface to configure the Switch, then connect the supplied serial cable to the Switch’s Console port, and tighten the captive retaining screws. Connect the other end to your PC’s serial port. (This PC must be running the VT100 terminal emulation software, such as HyperTerminal.)

7.Connect the supplied power cord to the Switch’s power port, and plug the other end into an electrical outlet.

WARNING: Make sure you use the power cord that is supplied with the Switch. Use of a different power cord could damage the Switch.

8.Power on the network devices connected to the Switch. Each active port’s corresponding Link/Act LED will light up on the Switch. If a port has an active Gigabit connection, then its corresponding Gigabit LED will also light up.

NOTE: If you need to reset the Switch, unplug the power cord from the back of the Switch. Wait a few seconds and then reconnect it.

8-Port 10/100 Ethernet Switch with Webview

8

Image 14

Contents Port 10/100 Ethernet Switch with Webview Icon Descriptions About This GuideAbout This Guide Online ResourcesTable of Contents Port 10/100 Ethernet Switch with Webview Iii Table of Contents Appendix G Contact Information Appendix B IntroductionAppendix F Regulatory Information Welcome Chapter IntroductionIntroduction SRW208 Front Panel Chapter Product OverviewProduct Overview SRW208G Front PanelSRW208L Front Panel SRW208P/SRW208MP Front PanelBack Panel Positioning the Switch Chapter InstallationInstallation Placement OptionsRack-Mount Placement Wall-Mount Placement Hardware Installation Chapter Configuration Using Console Interface Connecting to the Switch through a Telnet SessionSwitch Main Menu System Configuration MenuManagement Settings SSH Configuration User & Password Settings IP Configuration Https Configuration Port Configuration Port StatusHelp Accessing the Web-based Utility Chapter Advanced ConfigurationAdvanced Configuration Setup SummarySystem Information Setup Network SettingsIP Configuration PoE InformationSetup Time Port Management Port SettingsPort Configuration Detail Port Management Link Aggregation Link Aggregation DetailPort Management PoE Power Settings Port Management LacpSingle Vlan Vlan Management Port SettingsVlan Management Create Vlan Vlan RangeVlan Management Ports to Vlan Vlan Management Vlan to PortsJoin Vlan Detail Vlan Management GvrpStatistics Rmon Statistics Statistics Rmon History Log TableStatistics Rmon Alarms Rmon HistoryStatistics Rmon Events Add EventStatistics Port Utilization Statistics 802.1x StatisticsStatistics Gvrp Statistics ACL IP based ACLACL MAC based ACL Security ACL Binding Security RadiusSecurity TACACS+ Security Ports Security Security 802.1x SettingsSetting Timer Security Multiple Hosts QoS QoS CoS SettingsSecurity Storm Control CoS Default QoS Queue SettingsQoS Dscp Settings QoS BandwidthQoS Basic Mode QoS Advanced ModeNew Class Map Out of Profile DscpPolicy Name New Aggregate Policer Spanning TreeSpanning Tree STP Status Spanning Tree Global STP Global SettingBridge Settings Spanning Tree STP Port Settings Spanning Tree Rstp Port SettingsSpanning Tree Mstp Properties Established by the deviceSpanning Tree Mstp Instance Settings Multicast Igmp Snooping Multicast Bridge Multicast Snmp Global ParametersSnmp Views Snmp Group Profile Snmp Group MembershipSnmp Communities Base TableAdvanced Table Snmp Notification FilterSnmp Notification Recipient Admin User Authentication Admin Static AddressQuery Admin Dynamic AddressAdmin Logging Admin Port Mirroring Admin Cable TestBackup Admin Save ConfigurationAdmin Firmware Upgrade Via TftpAdmin Server Logs Admin RebootAdmin Factory Defaults Admin Memory Logs Admin Flash LogsFiber Optic Cabling Appendix a About Gigabit Ethernet Fiber Optic CablingGigabit Ethernet Startup Menu Procedures Appendix B IntroductionDownloading Using Xmodem Appendix C Glossary GlossaryGlossary Smtp Simple Mail Transfer Protocol The standard e Appendix C Appendix D Specifications SpecificationsQoS Specifications SRW208L SRW208MP Limits Bandwidth Intensive Video Traffic to Only Requestors Support 256 multicast groups Ethernet Exclusions and Limitations Warranty InformationObtaining Warranty Service Warranty Information Technical SupportFCC Statement Safety NoticesRegulatory Information Industry Canada StatementRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Appendix G Contact Information

Related manuals

Manual 3 pages 51.04 Kb

Manual 142 pages 37.07 Kb

Manual 3 pages 34.25 Kb