Linksys SRW224G4P manual Setup Time, Set Time

Page 20

Chapter 5

Configuring the Switch

IP Address  Address of the VLAN interface that is allowed management access.. Valid IP addresses consist of four numbers, 0 to 255, separated by periods.. (Default: 192.168.1.254)

Subnet Mask  This mask identifies the host address bits used for routing to specific subnets.. (Default: 255.255.255.0)

Default Gateway  IP address of the gateway router between this device and management stations that exist on other network segments.. (Default: 0.0.0.0)

DNS Server  Enter the IP address of the DNS server into the text field.. A second DNS address can be specified in the additional text field provided..

Click Save Settings to save the changes..

Click Restart DHCP to assign a new IP address using DHCP..

Setup > Time

Simple Network Time Protocol (SNTP) allows the Switch to set its internal clock based on periodic updates from a time server (SNTP or NTP).. Maintaining accurate time on the Switch enables the system log to record meaningful dates and times for event entries.. If the clock is not set, the Switch will only record the time from the factory default set at the last bootup.. When the SNTP client is enabled, the Switch periodically sends a request for a time update to a configured time server.. You can configure up to two time server IP addresses.. The Switch will attempt to poll each server in the sequence..

Setup > Time

Set Time

Set the system time manually  This option allows you to set the time and date manually for the Switch..

Set the system time using Simple Network Time Protocol (SNTP) automatically  Sets the system clock automatically using SNTP..

Manual

Hours  The hour is entered here..

Minutes  The minutes is entered here..

Seconds  The seconds is entered here..

Month  The month is entered here..

Day  The day is entered here..

Year  The year is entered here..

Automatic

Sets the system clock automatically using SNTP..

Time Zone  Set the time zone by selecting it from the drop-down menu..

Daylight Savings  Enable daylight saving time by checking the checkbox.. Then set USA, Europe, or custom daylight saving time by clicking the appropriate option..

Time Set Offset  Custom daylight saving time is set by entering the time difference in minutes into the Time Set Offset field.. Set the date for this offset by entering the day and month (DD/MM) in the From and To fields..

Recurring  To enable a recurring custom daylight savings time, check the Recurring checkbox.. Set the day, week, and month the time difference will be recurring (From and To) by using the drop-down menus.. Set the time (From and To) of the recurrence using the field provided (HH:MM)..

SNTP Servers 

Sets the IP address of up to two SNTP servers.. Server 1  Set the IP address of the SNTP server..

Server 2  Set the IP address of an additional SNTP server..

Polling Internal (16-16384 sec)  The value entered here determines the number of seconds between each time the Switch contacts the SNTP server for an update..

24-Port 10/100 + 4-Port Gigabit Switch with WebView and Power over Ethernet

16

Page 19 Page 21
Image 20
Page 19 Page 21
Contents User Guide Table of Contents ACL Appendix E Contact Information Appendix a About Gigabit Ethernet and Fiber Optic CablingAbout This Guide Icon DescriptionsOnline Resources Copyright and TrademarksChapter Chapter IntroductionChapter Product Overview Front PanelBack Panel Side PanelOverview Pre-Installation ConsiderationsPlacement Options Hardware Installation Uplinking the SwitchDesktop Placement Rack-Mount PlacementChapter Configuration Using Console Interface Configuring the HyperTerminal ApplicationLogin Switch Main MenuSystem Configuration Menu System ConfigurationManagement Settings User & Password SettingsIP Configuration IP Address SettingsFile Management Restore System Default SettingsReboot System Port Configuration PoE ConfigurationPort Status Back to Main MenuSystem PoE Configuration Port PoE ConfigurationPort PoE Status LogoutDevice Information SetupSetup Summary Setup Network Settings System InformationPoE Information IdentificationSetup Time Set TimePort Management Port Management Port SettingsEdit Port Settings Port Management Link Aggregation Port Broadcast ControlPort Management PoE Power Settings Global SettingPort Setting Port Management LacpVlan Management Port Settings Vlan ManagementVlan Management Create Vlan Create VlanVlan Management Ports to Vlan Vlan Management Vlan to PortsStatistics Rmon History StatisticsStatistics Rmon Statistics Statistics Rmon Alarms Statistics Rmon EventsStatistics Port Utilization Statistics 802.1x StatisticsACL IP based ACL ACL MAC based ACLSecurity Authentication Servers Radius Server SettingSecurity Security ACL BindingSecurity 802.1x Settings Tacacs Server SettingSecurity Ports Security Security Https Settings Security Management ACLSecurity SSH Settings Security SSH Host-Key SettingsCoS to Queue QoS CoS SettingsQoS QoS Queue Settings QoS Dscp SettingsQueue Settings Port to CoSQoS DiffServ Settings Class MapPolicy Map QoS Bandwidth Spanning TreeQoS DiffServ Port Binding Spanning Tree STP Status Spanning Tree Global STPSpanning Tree STP Port Settings Spanning Tree STP Port Settings STP Port Setting Detail Spanning Tree Rstp Port Settings Spanning Tree Mstp Instance Settings Spanning Tree Mstp PropertiesSpanning Tree Mstp Interface Settings Multicast Multicast Global Settings Multicast Static Member PortsMulticast Router Ports Query Multicast Static Router PortsMulticast Member Ports Query Snmp Global Parameters Snmp Views Snmp Group ProfileUser Authentication Snmp Group MembershipSnmp Communities Data PrivacyAdmin Admin User AuthenticationSnmp Notification Recipient SNMPv1,2Admin Forwarding Database Static Address SettingAddress Aging Dynamic Address QuerySyslog Admin LogSystem Logging Admin Port Mirroring Smtp SettingAdmin Save Configuration Admin Cable TestAdmin Ping Admin Http Upgrade Admin Jumbo FrameAdmin Firmware Upgrade Admin Reboot Admin Factory DefaultFiber Optic Cabling Appendix a About Gigabit Ethernet Fiber Optic CablingGigabit Ethernet Appendix B Appendix B GlossaryGlossary Smtp Simple Mail Transfer Protocol The standard e Appendix B Appendix C Specifications Appendix CSpecifications Appendix D Warranty and Regulatory Information Limited WarrantySafety Notices FCC StatementIndustry Canada Canada IC StatementDansk Danish Miljøinformation for kunder i EU La Directiva 2002/96/CE de la UE exige que los equipos que Norsk Norwegian Miljøinformasjon for kunder i EU WEB For additional information, please visit Appendix E
Top Page Image Contents