Linksys SRW224G4P manual Spanning Tree, QoS DiffServ Port Binding, QoS Bandwidth

Page 39

Chapter 5

Configuring the Switch

•Exceed Action  Specifies whether the traffic that exceeds the specified rate or burst will be dropped or the DSCP service level will be reduced..

•Set  DecreasesDSCPpriorityforoutofconformance traffic.. (Range: 0-63)..

•Drop  Drops non-conforming traffic..

Add  Adds the specified criteria to the policy map.. Remove  Deletes a class from a policy..

Add classes to a selected policy and set the Action, Meter, Rate, Burst and Exceed values using the drop-down menus and fields provided then click Add..

QoS > DiffServ Port Binding

QoS > DiffServ Port Binding

This function binds a policy map to the ingress queue of a particular interface.. You must first define a class map, set an ACL mask to match the criteria defined in the class map, then define a policy map, and finally bind the service policy to the required interface.. You can only bind one policy map to an interface.. The current firmware does not allow you to bind a policy map to an egress queue..

Check the checkbox and choose a Policy Map for a port from the drop-down menu..

Click Save Settings to save the changes..

QoS > Bandwidth

This function allows the network manager to control the maximum rate for traffic transmitted or received on an interface.. Rate limiting is configured on interfaces at the edge of a network to limit traffic coming out of the Switch.. Traffic that falls within the rate limit is transmitted, while packets that exceed the acceptable amount of traffic are dropped..

Rate limiting can be applied to individual ports or LAGs.. When an interface is configured with this feature, the traffic rate will be monitored by the hardware to verify conformity.. Non-conforming traffic is dropped, conforming traffic is forwarded without any changes..

QoS > Bandwidth

Port  Displays the port or LAG number..

Status  Enables the rate limit (input or output) for the port or LAG.. (Default: Disabled)

Rate Limit (Kbits/sec)  Sets the rate limit level for the port or LAG.. For Fast Ethernet ports the default is 100000 Kbits/sec (Range: 64-100000).. For Gigabit Ethernet ports the default is 1000000 Kbits/sec (Range: 64-1000000)..

LAG  Indicates if ports are members of a LAG.. To configure a rate limit for LAGs, go to the table entry for the LAG number, which is listed after ports Gig 1 and Gig 2 at the end of the table..

Set the Input Rate Limit Status or Output Rate Limit Status, then set the rate limit for individual interfaces or LAGs, then click Save Settings..

Spanning Tree

The Spanning Tree Algorithm (STA) can be used to detect and disable network loops, and to provide backup links between switches, bridges or routers.. This allows the Switch to interact with other bridging devices (that is, an STA-compliant switch, bridge or router) in your network to ensure that only one route exists between any two stations on the network, and provide backup links which automatically take over when a primary link goes down..

24-Port 10/100 + 4-Port Gigabit Switch with WebView and Power over Ethernet

35

Page 38 Page 40
Image 39
Page 38 Page 40
Contents User Guide Table of Contents ACL Appendix a About Gigabit Ethernet and Fiber Optic Cabling Appendix E Contact InformationCopyright and Trademarks About This GuideIcon Descriptions Online ResourcesChapter Introduction ChapterFront Panel Chapter Product OverviewSide Panel Back PanelPre-Installation Considerations Placement OptionsOverview Rack-Mount Placement Hardware InstallationUplinking the Switch Desktop PlacementConfiguring the HyperTerminal Application Chapter Configuration Using Console InterfaceSystem Configuration LoginSwitch Main Menu System Configuration MenuUser & Password Settings Management SettingsIP Address Settings IP ConfigurationRestore System Default Settings Reboot SystemFile Management Back to Main Menu Port ConfigurationPoE Configuration Port StatusLogout System PoE ConfigurationPort PoE Configuration Port PoE StatusSetup Setup SummaryDevice Information Identification Setup Network SettingsSystem Information PoE InformationSet Time Setup TimePort Management Port Settings Edit Port SettingsPort Management Port Broadcast Control Port Management Link AggregationPort Management Lacp Port Management PoE Power SettingsGlobal Setting Port SettingCreate Vlan Vlan Management Port SettingsVlan Management Vlan Management Create VlanVlan Management Vlan to Ports Vlan Management Ports to VlanStatistics Statistics Rmon StatisticsStatistics Rmon History Statistics Rmon Events Statistics Rmon AlarmsStatistics 802.1x Statistics Statistics Port UtilizationACL MAC based ACL ACL IP based ACLSecurity ACL Binding Security Authentication ServersRadius Server Setting SecurityTacacs Server Setting Security 802.1x SettingsSecurity Ports Security Security Management ACL Security Https SettingsSecurity SSH Host-Key Settings Security SSH SettingsQoS CoS Settings QoSCoS to Queue Port to CoS QoS Queue SettingsQoS Dscp Settings Queue SettingsClass Map QoS DiffServ SettingsPolicy Map Spanning Tree QoS DiffServ Port BindingQoS Bandwidth Spanning Tree Global STP Spanning Tree STP StatusSpanning Tree STP Port Settings Spanning Tree STP Port Settings STP Port Setting Detail Spanning Tree Rstp Port Settings Spanning Tree Mstp Properties Spanning Tree Mstp Instance SettingsSpanning Tree Mstp Interface Settings Multicast Multicast Static Member Ports Multicast Global SettingsMulticast Static Router Ports Multicast Member Ports QueryMulticast Router Ports Query Snmp Global Parameters Snmp Group Profile Snmp ViewsData Privacy User AuthenticationSnmp Group Membership Snmp CommunitiesSNMPv1,2 AdminAdmin User Authentication Snmp Notification RecipientDynamic Address Query Admin Forwarding DatabaseStatic Address Setting Address AgingAdmin Log System LoggingSyslog Smtp Setting Admin Port MirroringAdmin Cable Test Admin PingAdmin Save Configuration Admin Jumbo Frame Admin Firmware UpgradeAdmin Http Upgrade Admin Factory Default Admin RebootAppendix a About Gigabit Ethernet Fiber Optic Cabling Gigabit EthernetFiber Optic Cabling Appendix B Glossary Appendix BGlossary Smtp Simple Mail Transfer Protocol The standard e Appendix B Appendix C Appendix C SpecificationsSpecifications Limited Warranty Appendix D Warranty and Regulatory InformationIC Statement Safety NoticesFCC Statement Industry Canada CanadaDansk Danish Miljøinformation for kunder i EU La Directiva 2002/96/CE de la UE exige que los equipos que Norsk Norwegian Miljøinformasjon for kunder i EU WEB For additional information, please visit Appendix E
Top Page Image Contents