Linksys SRW224G4P manual Spanning Tree Rstp Port Settings

Page 43

Chapter 5

Configuring the Switch

Priority  Defines the priority used for this port in the Spanning Tree Protocol.. If the path cost for all ports on a switch are the same, the port with the highest priority (i..e.., lowest value) will be configured as an active link in the Spanning Tree.. This makes a port with higher priority less likely to be blocked if the Spanning Tree Protocol is detecting network loops.. Where more than one port is assigned the highest priority, the port with lowest numeric identifier will be enabled..

Default: 128

Range: 0-240, in steps of 16

Port Fast  You can enable this option if an interface is attached to a LAN segment that is at the end of a bridged LAN or to an end node.. Since end nodes cannot cause forwarding loops, they can pass directly through to the spanning tree forwarding state.. Specifying Edge Ports provides quicker convergence for devices such as workstations or servers, retains the current forwarding database to reduce the amount of frame flooding required to rebuild address tables during reconfiguration events, does not cause the spanning tree to initiate reconfiguration when the interface changes state, and also overcomes other STA-related timeout problems.. However, remember that Edge Port should only be enabled for ports connected to an end-node device.. (Default: Disabled)

Spanning Tree > RSTP Port Settings

Spanning Tree > RSTP Port Settings

The Port Information display the current status of the ports in the Rapid Spanning Tree..

Port  Displays the port number..

State  Shows if Rapid Spanning Tree has been enabled on this interface..

Status  Displays current state of this port within the Spanning Tree:

Discarding  Port receives STA configuration messages, but does not forward packets..

Learning  Porthastransmittedconfigurationmessages for an interval set by the Forward Delay parameter without receiving contradictory information.. Port address table is cleared, and the port begins learning addresses..

Forwarding  Port forwards packets, and continues learning addresses..

Role  Roles are assigned according to whether the port is part of the active topology connecting the bridge to the root bridge (i..e.., root port), connecting a LAN through the bridge to the root bridge (i..e.., designated port), or is the MSTI regional root (i..e.., master port); or is an alternate or backup port that may provide connectivity if other bridges, bridge ports, or LANs fail or are removed.. The role is set to disabled (i..e.., disabled port) if a port has no role within the spanning tree..

Forward Transitions  The number of times this port has transitioned from the Learning state to the Forwarding state..

Operational Edge Port  This parameter is initialized to the setting for Administrative Edge Port in STP Port Setting detail, but will be set to false if a BPDU is received indicating that another bridge is attached to this port..

Operational Link Type  The operational point-to-point status of the LAN segment attached to this interface.. This parameter is determined by manual configuration or by auto-detection, as described for Administrative Link Type in the STP Port Setting detail..

Click the Detail button to configure Protocol Migration Test and Administrative Link Type.. Use the check box and dropdown menu provided to enable and select the mode, then click Apply..

Spanning Tree > RSTP Port Settings > RSTP Port Setting Detail

24-Port 10/100 + 4-Port Gigabit Switch with WebView and Power over Ethernet

39

Image 43
Contents User Guide Table of Contents ACL Appendix a About Gigabit Ethernet and Fiber Optic Cabling Appendix E Contact InformationCopyright and Trademarks About This GuideIcon Descriptions Online ResourcesChapter Introduction ChapterFront Panel Chapter Product OverviewSide Panel Back PanelPlacement Options Pre-Installation ConsiderationsOverview Rack-Mount Placement Hardware InstallationUplinking the Switch Desktop PlacementConfiguring the HyperTerminal Application Chapter Configuration Using Console InterfaceSystem Configuration LoginSwitch Main Menu System Configuration MenuUser & Password Settings Management SettingsIP Address Settings IP ConfigurationReboot System Restore System Default SettingsFile Management Back to Main Menu Port ConfigurationPoE Configuration Port StatusLogout System PoE ConfigurationPort PoE Configuration Port PoE StatusSetup Summary SetupDevice Information Identification Setup Network SettingsSystem Information PoE InformationSet Time Setup TimeEdit Port Settings Port Management Port SettingsPort Management Port Broadcast Control Port Management Link AggregationPort Management Lacp Port Management PoE Power SettingsGlobal Setting Port SettingCreate Vlan Vlan Management Port SettingsVlan Management Vlan Management Create VlanVlan Management Vlan to Ports Vlan Management Ports to VlanStatistics Rmon Statistics StatisticsStatistics Rmon History Statistics Rmon Events Statistics Rmon AlarmsStatistics 802.1x Statistics Statistics Port UtilizationACL MAC based ACL ACL IP based ACLSecurity ACL Binding Security Authentication ServersRadius Server Setting SecurityTacacs Server Setting Security 802.1x SettingsSecurity Ports Security Security Management ACL Security Https SettingsSecurity SSH Host-Key Settings Security SSH SettingsQoS QoS CoS SettingsCoS to Queue Port to CoS QoS Queue SettingsQoS Dscp Settings Queue SettingsClass Map QoS DiffServ SettingsPolicy Map QoS DiffServ Port Binding Spanning TreeQoS Bandwidth Spanning Tree Global STP Spanning Tree STP StatusSpanning Tree STP Port Settings Spanning Tree STP Port Settings STP Port Setting Detail Spanning Tree Rstp Port Settings Spanning Tree Mstp Properties Spanning Tree Mstp Instance SettingsSpanning Tree Mstp Interface Settings Multicast Multicast Static Member Ports Multicast Global SettingsMulticast Member Ports Query Multicast Static Router PortsMulticast Router Ports Query Snmp Global Parameters Snmp Group Profile Snmp ViewsData Privacy User AuthenticationSnmp Group Membership Snmp CommunitiesSNMPv1,2 AdminAdmin User Authentication Snmp Notification RecipientDynamic Address Query Admin Forwarding DatabaseStatic Address Setting Address AgingSystem Logging Admin LogSyslog Smtp Setting Admin Port MirroringAdmin Ping Admin Cable TestAdmin Save Configuration Admin Firmware Upgrade Admin Jumbo FrameAdmin Http Upgrade Admin Factory Default Admin RebootGigabit Ethernet Appendix a About Gigabit Ethernet Fiber Optic CablingFiber Optic Cabling Appendix B Glossary Appendix BGlossary Smtp Simple Mail Transfer Protocol The standard e Appendix B Appendix C Appendix C SpecificationsSpecifications Limited Warranty Appendix D Warranty and Regulatory InformationIC Statement Safety NoticesFCC Statement Industry Canada CanadaDansk Danish Miljøinformation for kunder i EU La Directiva 2002/96/CE de la UE exige que los equipos que Norsk Norwegian Miljøinformasjon for kunder i EU WEB For additional information, please visit Appendix E