Linksys SRW224G4P manual IP Configuration, IP Address Settings

Page 14

Chapter 4

Configuration Using the Console Interface

You can add up to five user accounts in addition to the default admin account.. The admin account cannot be deleted from the system..

To save the new user account information, use the arrow keys to select Save and press Enter..

IP Configuration

The IP Configuration screen displays four menu choices: IP Address Settings, HTTP/HTTPS, SNMP, and Network Diagnostics..

IP Configuration

IP Address Settings

The IP Address Settings screen allows you to set the IP information for the Switch..

IP Address Configuration

IP Address  This sets the Switch’s IP Address.. The default setting is 192..168..1..5..

Subnet Mask  This combined with the IP Address defines the Switch’s network address..

Default Gateway  This defines the IP Address for the default gateway of the network..

Management VLAN  Set the ID number of the Management VLAN.. This is the only VLAN through which you can gain management access to the Switch.. By default, all ports on the Switch are members of VLAN 1, so a management station can be connected to any port on the Switch.. However, if other VLANs are configured and you change the Management VLAN, you may lose management access to the Switch.. In this case, you should reconnect the management station to a port that is a member of the Management VLAN..

WARNING: Do not define the Management VLAN as a VLAN that has yet to be created.. If the VLAN does not exist already, the software will automatically create the VLAN but will not assign VLAN membership.. If this happens, the Switch cannot be managed via the web‑based utility until it has been reconfigured via the console interface..

IP Mode  Choose to have either a user-defined IP address or to have it assigned by DHCP or BOOTP..

HTTP/HTTPS

The HTTP/HTTPS screen allows you to set the Hyper Text Transfer Protocol server (web server) information for the Switch..

HTTP/HTTPS

HTTP Server  Enable or disable the Switch’s HTTP server function..

HTTP Server port  Set the TCP port that HTTP packets are sent and received from..

HTTPS Server  Enable or disable the Secure HTTP server function of the Switch..

HTTPS Server port  Set the TCP port that the HTTPS packets are sent and received from..

SNMP

The SNMP screen allows you to set the Switch’s SNMP settings..

24-Port 10/100 + 4-Port Gigabit Switch with WebView and Power over Ethernet

10

Page 13 Page 15
Image 14
Page 13 Page 15
Contents User Guide Table of Contents ACL Appendix E Contact Information Appendix a About Gigabit Ethernet and Fiber Optic CablingOnline Resources About This GuideIcon Descriptions Copyright and TrademarksChapter Chapter IntroductionChapter Product Overview Front PanelBack Panel Side PanelOverview Pre-Installation ConsiderationsPlacement Options Desktop Placement Hardware InstallationUplinking the Switch Rack-Mount PlacementChapter Configuration Using Console Interface Configuring the HyperTerminal ApplicationSystem Configuration Menu LoginSwitch Main Menu System ConfigurationManagement Settings User & Password SettingsIP Configuration IP Address SettingsFile Management Restore System Default SettingsReboot System Port Status Port ConfigurationPoE Configuration Back to Main MenuPort PoE Status System PoE ConfigurationPort PoE Configuration LogoutDevice Information SetupSetup Summary PoE Information Setup Network SettingsSystem Information IdentificationSetup Time Set TimePort Management Port Management Port SettingsEdit Port Settings Port Management Link Aggregation Port Broadcast ControlPort Setting Port Management PoE Power SettingsGlobal Setting Port Management LacpVlan Management Create Vlan Vlan Management Port SettingsVlan Management Create VlanVlan Management Ports to Vlan Vlan Management Vlan to PortsStatistics Rmon History StatisticsStatistics Rmon Statistics Statistics Rmon Alarms Statistics Rmon EventsStatistics Port Utilization Statistics 802.1x StatisticsACL IP based ACL ACL MAC based ACLSecurity Security Authentication ServersRadius Server Setting Security ACL BindingSecurity 802.1x Settings Tacacs Server SettingSecurity Ports Security Security Https Settings Security Management ACLSecurity SSH Settings Security SSH Host-Key SettingsCoS to Queue QoS CoS SettingsQoS Queue Settings QoS Queue SettingsQoS Dscp Settings Port to CoSQoS DiffServ Settings Class MapPolicy Map QoS Bandwidth Spanning TreeQoS DiffServ Port Binding Spanning Tree STP Status Spanning Tree Global STPSpanning Tree STP Port Settings Spanning Tree STP Port Settings STP Port Setting Detail Spanning Tree Rstp Port Settings Spanning Tree Mstp Instance Settings Spanning Tree Mstp PropertiesSpanning Tree Mstp Interface Settings Multicast Multicast Global Settings Multicast Static Member PortsMulticast Router Ports Query Multicast Static Router PortsMulticast Member Ports Query Snmp Global Parameters Snmp Views Snmp Group ProfileSnmp Communities User AuthenticationSnmp Group Membership Data PrivacySnmp Notification Recipient AdminAdmin User Authentication SNMPv1,2Address Aging Admin Forwarding DatabaseStatic Address Setting Dynamic Address QuerySyslog Admin LogSystem Logging Admin Port Mirroring Smtp SettingAdmin Save Configuration Admin Cable TestAdmin Ping Admin Http Upgrade Admin Jumbo FrameAdmin Firmware Upgrade Admin Reboot Admin Factory DefaultFiber Optic Cabling Appendix a About Gigabit Ethernet Fiber Optic CablingGigabit Ethernet Appendix B Appendix B GlossaryGlossary Smtp Simple Mail Transfer Protocol The standard e Appendix B Appendix C Specifications Appendix CSpecifications Appendix D Warranty and Regulatory Information Limited WarrantyIndustry Canada Canada Safety NoticesFCC Statement IC StatementDansk Danish Miljøinformation for kunder i EU La Directiva 2002/96/CE de la UE exige que los equipos que Norsk Norwegian Miljøinformasjon for kunder i EU WEB For additional information, please visit Appendix E
Top Page Image Contents