3Com 2250-SFP Using SFP Tranceivers, Approved SFP Transceivers, Inserting an SFP Transceiver

Page 22

22INSTALLING THE SWITCH

Using SFP Tranceivers

The following sections describe how to insert an SFP transceiver into an SFP slot.

SFP transceivers are hot-insertable and hot-swappable. You can remove them from and insert them into any SFP port without having to power down the Switch.

Approved SFP Transceivers

The following list of approved SFP transceivers is correct at the time of publication:

3CSFP91 SFP (SX)

3CSFP92 SFP (LX)

To access the latest list of approved SFP transceivers for the Switch on the 3Com Web site, enter this URL into your Internet browser:

http://www.3Com.com

3Com recommends using 3Com SFPs in the Switch. If you insert an SFP transceiver that is not supported, the Switch will not recognize it.

Inserting an SFP Transceiver

To be recognized as valid, the SFP transceiver must have the following characteristics:

1000BASE-SX or 1000BASE-LX media type:

1000BASE-SX SFP transceiver

Use this transceiver to connect the Switch directly to a multimode fiber-optic cable.

1000BASE-LX SFP transceiver

Use this transceiver to connect the Switch directly to a single mode fiber-optic cable or to multi- mode fiber using a conditioned launch cable.

If the SFP transceiver is faulty, it will not operate within the Switch. See “Troubleshooting” on page 75.

To activate the SFP port:

1Hold the transceiver so that the fiber connector is toward you and the product label is visible, as shown in Figure 5. Ensure the wire release lever is closed (in the upright position).

Image 22
Contents Installation and User Guide 3Com Corporation 350 Campus Drive Marlborough MA Contents Snmp 3COM CLI Reference Guide Page About this Guide ConventionsDocumentation Comments Product RegistrationAutosensing of MDI/MDIX Connections Overview of the Baseline SwitchFeatures and Capabilities Autonegotiating 10/100 Mbps PortsPower-over-Ethernet Capability Physical FeaturesGigabit Combo Ports RJ-45/SFP Front Panel RJ-45 10/100 PortsGigabit Combo Ports RJ-45/SFP 10/100BASE-TX Link/Activity Status LEDs SFP Mode Power LED Rear PanelPackage Contents Installing the Switch Important Safety InformationPositioning the Switch Importante Avviso di SicurezzaUsing the Mounting Kit Rack-Mounting or Free-StandingMontagesatz Anweisungen Supplying Power to the SwitchPlacing Units On Top of Each Other Checking for Correct Operation Status MeaningApproved SFP Transceivers Using SFP TranceiversInserting an SFP Transceiver Performing Spot Checks Removing an SFP TransceiverRefer to Troubleshooting on Requirements for Accessing the Web Interface Using the Console Command Line Interface CLICLI Summary with Default IP Address Logging On to the Web Interface CLI Summary with Assigned IP AddressNavigating the Web Interface MenuMenu Item Description Snmp Buttons Port StatusRunning the 3Com Switch Detect Application 3Com Switch Detect Welcome Screen3Com Switch Detect Search Screen Connecting to the WEB Interface Configuration Overview Device Summary InformationDevice View Polling IntervalAutomatic IP Configuration Administration SettingsModifying the IP Address Settings Color KeyIP Setup Backup ConfigurationRestore Configuration Firmware UpgradeReboot ResetSystem Access Initialize, keep IP settingUser Summary Create UserModify User Remove UserSystem Name SetupSystem Time Snmp Add Configuring VLANsSnmp Remove Vlan Setup Screen Modify VlanModify Port RenameRemove Port DetailForwarding Tagged/Untagged Frames Sample Vlan ConfigurationsVlan Detail Setting Up Two VLANs on the Same Switch Setting Up Vlan Across Two SwitchesTagged Vlan Configuration Spanning TreeSummary Spanning Tree Summary ScreenPort Setup Spanning Tree Setup ScreenSpanning Tree Port Setup Screen Igmp Snooping & QueryBroadcast Storm Broadcast Storm Summary ScreenQoS VoIP Traffic Settings ModifyQoS VoIP Setup Screen OUI Summary OUI AddPoE 3CBLSF26-PWR only QoS OUI Modify ScreenConfiguring Port Settings AdministrationPort Administration Summary Screen DetailPort Administration Setup Screen Speed/Duplex for 1000 Mbps ConnectionsLink Aggregation Guidelines for Creating TrunksCreate Link Aggregation Summary ScreenUse the Remove tab to delete a link aggregation group Statistics SecurityRadius Client 802.1X Settings Configure802.1X Summary Screen Monitoring Address TablePort Mirroring Port SummaryUse the Setup tab to create a port mirror session Cable Diagnostics Cable Diagnostic Summary ScreenDiagnostics Cable Diagnostic ScreenConfiguring the Switch from the WEB Interface Troubleshooting Resetting to Factory DefaultsForgotten Static IP Address Solving LED IssuesFiber cable is connected, but the Module Active LED is off Link/Activity LED is on, but network performance is poor If the Problem PersistsAll ports appear to show continual activity Troubleshooting Troubleshoot Online Access Software Downloads Purchase Value-Added ServicesRegister Your Product Telephone Technical Support and Repair Contact UsCountry Telephone Number Latsupportanc@3com.com Physical 3CBLSF26 Related StandardsEnvironmental Electrical3CBLSF26PWR Related Standards Physical 3CBLSF50 Related StandardsEnvironmental ElectricalAppendix B Technical Information PIN-OUTS Console CablePC-AT Serial Cable Null Modem CableModem Cable Ethernet Port RJ-45 Pin Assignments Pin Number 10/100 1000Appendix C PIN-OUTS Console Port Getting Started with the Command Line InterfaceLogging on to the CLI Automatic Logout CLI CommandsConcurrent CLI Sessions Syntax Default Configuration Ping ParametersIpSetup 255.255.255.0Upgrade Following example resets the Switch to factory defaults InitializePassword LogoutRegulatory Notices 100 Auto-negotiation 1000BASE-TBandwidth Category 5e Cables Category 3 CablesCategory 5 Cables Category 6 CablesIeee 802.1D Full DuplexHalf Duplex Ieee 802.1QLink Aggregation Power over EthernetLayer MAC AddressSubnet Address SwitchServer Subnet MaskVlan Index NumbersIndex