3Com 10002211 This message is immediately overwritten with, Power supply +5-volt input has failed

Page 28

22COREBUILDER 6000 EXTENDED SWITCHING SOFTWARE REVISION 8.2.3

To remove a faulty power supply and replace it with a new unit, follow these steps:

1Turn off the power supply according to the safety and removal procedures in the Installation Guide that is shipped with the new power supply. The system control panel displays the following message (where n designates power supply 1 or power supply 2):

Power Supply n: Input Failure

2Remove the power supply. The system generates a sound, and the system control panel displays the following message:

Power supply n extracted.

3Insert the new power supply, following the safety warnings and instructions in the Installation Guide that comes with the new power supply. The system displays this message:

Inserted

This message is immediately overwritten with:

Input Failure

4Turn on the power supply. The system generates a sound and the system control panel displays this message:

Input restored

Power Supply Warning Messages. This release of system software now displays these power supply warning messages on the control panel when appropriate:

■+5V Failure

The power supply +5-volt input has failed.

■+12V Failure

The power supply +12-volt input has failed.

■ +5V Restored

The power supply +5-volt input is restored.

Image 28

Contents CoreBuilder Extended Switching Software Revision October 17 CorebuilderUnited States Government Legends Contents IP Multicast Routing Vlans on the Corebuilder System 3COM Corporation Limited Warranty Overview CoreBuilder 6000 Extended Switching software from 3ComDated May 30 Corebuilder 6000 Extended Switching Software Revision Updating Your System Software Remove diskette #2 using the following command Remove diskette #1 using the following commandRemove diskette #3 using the following command Remove diskette #5 using the following command Remove diskette #4 using the following commandFollowing ﬁles are now in your /usr/lp6000R directory Software on Loading SystemLMM+ \3com\lp6000R\image\lp6000R User DocumentationRevision 8.2.3? What’s New atCorrections implemented at this release To deﬁne an IP interface Enter the number of the Vlan whose interface you are deﬁning AxFDDI axFDDI group AxFDDIHistory axFDDI groupTo enable Spanning Tree transitions, enter To disable Spanning Tree transitions, enterDisplaying Bridge Information System prompts you for slot numbersSample display of bridge port information Revision 8.2.0? Corrections that are implemented at this releaseWhat’s New at Revision 8.2.0? You receive the prompt to select each port’s duplex mode System displays this messageDefault To select the default all, press Return FTP Packet Filter Program Transfers via Snmp ﬁrst telnet session is disconnected and the system displays Sample screen showing the display after the changes What’s New at Revision 8.2.0? Power supply +5-volt input has failed Power supply +12-volt input has failedPower supply +5-volt input is restored This message is immediately overwritten withSystem Issues System nvdata reset System Issues Known Problems New Imports section now looks like thisReceived ftpCommand Quit not completed errno Corebuilder 6000 Extended Switching Software Revision Snmp MIB Files Support for IP routing on the Fddi Switching Module FSM Configurable Source Route hop count limit Efsm LpBridgePortAddressLearnedEvent Corebuilder 6000 Extended Switching Software Revision IP Multicast Routing Following parametersDisabling Dvmrp EnablingDisabling Igmp Multicast Administering IPInterfaces Multicast interface Example multicast interface conﬁguration for the slotDisabling Multicast Interfaces Enabling Multicast InterfacesAdministering Multicast TunnelsExample Address of the remote multicast routerAssociate a multicast tunnel Enter the IP address of the destination multicast routerEnter the Dvmrp metric value of the tunnel Enter the Time To Live TTL threshold of the tunnelDisplaying Routes Following display shows all available multicast routes Table A-1describes the ﬁelds in the route displayDisplaying Multicast CacheFollowing display shows the multicast cache conﬁguration Table A-2describes the ﬁelds in the CacheDisplay Remote Monitoring Rmon B Technology CoreBuilder ImplementationSegment being monitored Table B-3 Supported Ethernet and Fddi Frame Size Buckets Rmon Groups Setting Alarm Thresholds Example of an Alarm ThresholdRmon Groups 3Com Transcend Rmon Agents Management Information Base MIB Figure B-3 Example of an Rmon MIB Counter Object About VLANs CoreBuilder system, VLANs allow you toCreate ﬁrewalls LocationsAppendix C Vlans on the Corebuilder System Protocol Suite Layer 3 Addressing Information SNAModifying the Default Vlan How CoreBuilder System Makes Flooding DecisionsVlan Exception Flooding Overlapped IP VLANs Routing Between VLANs Administering Vlans Displaying Vlan InformationExample of a summary display for several VLANs Table D-1describes these statistics Deﬁning Vlan Information for aTraditional Bridge As an Efsm or a TMMEnter the subnetwork mask Information for An HSI Switch EngineDeﬁning Vlan Follow these steps to create a Vlan deﬁnition Enter the IP subnet address Enter the subnetwork mask Bridge vlan modify Bridge vlan remove Technical Support Access by Analog Modem Type go threecom Regional Sales Office Telephone Number 3Com Corporation Returning Products for Repair Page 3Com Corporation Limited Warranty Limitation of Liability